News Center
our commitment to nickbaler
  • The double-cylinder waste paper baler has the characteristics of good rigidity and stability, beautiful appearance, convenient operation and maintenance, safety and energy saving, and low investment cost of equipment basic engineering. waste paper baler is widely used in various waste paper factories, waste recycling companies and other units and enterprises. It is suitable for packaging and recycling waste paper, plastic straw, etc. It is to improve labor efficiency, reduce labor intensity, save manpower, and reduce transportation. Good equipment for cost.

    1. This machine is suitable for compressing and Baler loose materials such as waste paper and newspapers.

    2. This machine uses a high-performance, low-noise hydraulic circuit system, and uses imported hydraulic accessories; the whole machine has stable performance and low vibration.

    3. Reasonable double-cut scissors design improves the efficiency of cutting paper and prolongs the service life of the blade.

    4. Fast and simple wire binding device, low failure rate, easy to clean, maintain and repair.

    5. Freely set the package length and accurately record the package value.

    6. Easy to install, no special site infrastructure is required.

    微信图片_20210914173443 拷贝.jpg

    After the waste paper, waste cardboard and other materials are compressed and bundled by Nick Machinery's automatic hydraulic baler, it is easy to store and stack and reduce transportation costs. https://www.nickbaler.net


    21-10-11
  • With the increasing number of waste materials and the development of hydraulic technology, metal balers, metal shears, and metal chip briquetting machines are increasingly used in various material recycling processing points. Therefore, it is very important to ensure the normal operation of the hydraulic equipment system and increase the reliability of the work. The correct selection of the type and viscosity of the hydraulic oil is the first condition to ensure the long-term and reliable operation of the system.

    On the other hand, when the hydraulic equipment system fails, it is also very important to be able to quickly find the cause and effectively solve it. The hydraulic equipment is composed of mechanical, hydraulic, electrical and instrumentation devices. Therefore, when analyzing the failure of the hydraulic equipment system, it is necessary to understand the transmission principle, structural characteristics, components and material configuration of the entire hydraulic system. Since the hydraulic equipment system is a sealed and pressurized system, it is difficult to observe the flow of oil in the pipeline, the movement of the internal parts of the hydraulic component and whether the seal is damaged, so it is difficult to analyze the cause of the failure and determine the location of the failure.

    There are many reasons for the failure of hydraulic equipment systems such as metal balers, metal shears, and metal chip briquetting machines. Most of the reasons are: mechanical failure of the equipment, such as unreasonable design of the hydraulic equipment system, incorrect installation clearance, and hydraulic components Quality problems, improper selection of seals, etc., and operating errors caused hydraulic system failures---this refers to hydraulic equipment systems that are caused by improper operation of the operator during normal operation, such as incorrect operation sequence or incorrect opening and closing of valves, and normal operation When the power supply is suddenly interrupted, the temperature or pressure of the hydraulic oil is too high during work, no action is taken, the wrong oil is added when refueling, and the existing oil volume of the oil tank is too much or too little. In addition, the quality of the hydraulic oil causes the failure of the hydraulic equipment system. This is mostly caused by improper oil selection or the use of unqualified oil. It may also be caused by the hydraulic oil being used for a long time, and the new oil is not replaced in time.

    DSCF2653 拷贝.jpg

    All models of Nick Machinery's metal baler adopt hydraulic drive device, which can be operated manually or automatically controlled by PLC. Contact consultation telephone 86-29-86031588


    21-10-09
  • Metal balers, metal shears, and scrap briquetting machines are in the machine running-in period within a few months before the new machine is used. During the operation period, the operating conditions should be checked frequently, such as the maintenance of the machine parts, whether the screws are loose, and whether there are any Abnormal noise, whether the oil temperature rises abnormally, whether the hydraulic oil is quickly degraded, whether there is oil leakage in the tubing, whether the operating conditions meet the regulations, etc.

    Before starting the machine, check whether there are any signs of screw loosening, whether the oil level is normal, and whether there is any oil leakage at the oil circuit joints.

    Do not apply the load immediately after starting up. It is necessary to implement a period of no-load idling to make the hydraulic circuit circulate normally before applying the load, and confirm that the operation is normal. When the load is running, observe whether the pressure is too high or too low, and pay attention to it during operation. Whether the oil temperature changes and the sound of the hydraulic pump are normal. The hydraulic pump has low initial wear and is easily affected by bubbles and dust. Poor lubrication at high temperatures or overloaded operating conditions will cause adverse consequences and make the hydraulic pump emit abnormal sounds. Pay attention to the adjustment of each hydraulic valve. It is necessary to fully understand the use of pressure control valves, flow control valves and directional control valves, and pay special attention to the adjustment range and limits. Otherwise, adjustment errors will not only damage the machinery, but also pose a threat to safety. The filter should be removed and cleaned regularly, and the status of the filter screen and the dirt adsorbed on the network should be checked, and the quality, quantity and size of the filter should be analyzed, so that the degree of pollution in the loop can be observed, and the source of the pollution can be inferred based on this. Regularly check the deterioration, discoloration and pollution of the hydraulic oil to ensure the normality of the hydraulic transmission medium.

    mmexport1492234423664 拷贝.jpg

    In addition, for such an automatic packaging device, its operation is also very simple. You only need to understand the basic operations to easily control it. https://www.nickbaler.net


    21-10-09
  • In the face of the coming cold weather, the metal baler faced the greatest test. The metal baler is a steel weldment. The hydraulic components and hydraulic oil in the whole machine are the most able to withstand the test of cold weather. That is to say, the quality of the parts of these parts is good or bad, which directly affects whether the metal baler can be used in Normal work in any cold weather.

    Hydraulic Components

    The sealing ring in the cylinder of the metal baler is made of high-quality plastic synthetic products. Its quality directly affects its flexibility in cold weather. If a poor quality sealing ring is used, it will be under cold conditions. Oil leakage will occur due to working friction. Cold weather will also affect the sealing performance of the "O" ring.

    Hydraulic oil in the tank

    2 拷贝.jpg

    As far as the metal baler is concerned, its hydraulic oil is the most fearful of cold, and also the most feared component of winter. In cold weather, it will freeze and it will not be able to work, so pay special attention to it in cold weather Protection of hydraulic oil. https://www.nickbaler.net


    21-10-09
  • Since the new century, the degree of numerical control of metal shearing machines has become more and more. In the next few years, there will be more room for development of shearing machine products, and its demand will show an outstanding trend of gradual increase. Following people's seriousness on the production power, the equipment has a broad development space, and the demand for shopping malls continues to increase. Judging from the existing shearing machine planning, future growth space and the increasing trend at that time, shearing machine equipment has gradually become a market that cannot be underestimated by shearing machine manufacturers.

    In order to expand the shearing machine marketing market, firmly believe that the market is the basic concept of the lifeline of industrial economic development, make full use of the capital market, and strive to build the version of the industrial economy. On the basis of the original equipment, after many trials and improvements, a new series of shears was introduced. The shearing machine cuts and does not block the host. The particle size of the material after shearing is very suitable for use as a raw material for production, providing a solution for the regenerative shearing process.

    Metal shearing machine potential and characteristics

    1. The structure is simple, the body has no moving parts, no special auxiliary equipment is needed, and it occupies a small area with less manufacturing and installation.

    2. It is easy to maintain, low maintenance cost, and has a higher separation efficiency for dust smaller than 10 microns.

    3. The shearing machine has stable performance, is not restricted by gas and temperature, has no special requirements for dust, and has a wide range of applications.

    工字钢剪切机+槽钢剪切机+废金属剪切机 拷贝.jpg

    The development of the shearing machine industry has now been in the forefront of development. We understand that we must have and confidently develop our own inherent mode of development, so as to make the shearing machine industry strong and invincible. https://www.nickbaler.net


    21-10-08
  • 1. Clean

    The outside of the waste paper baler is tidy, and there is no oil on all sliding surfaces, chains, racks, oil pumps, oil holes, etc., and no oil leaks at all parts. The chips, debris and dirt around the waste paper baler should be cleaned up;

    2. Neat

    Place materials, finished paper, finished paper, and power lines in the venue in an orderly manner;

    3. Good lubrication

    Fill or change the oil on time, keep the oil, no dry friction, normal oil pressure, bright oil mark, unobstructed oil path, and the oil quality meets the requirements;

    4. Security

    Observe the safety operation regulations, do not overload the equipment, the safety protection device of the waste paper baler is complete and reliable, and eliminate unsafe factors in time.

    3-2废纸 (2).jpg

    Nick Machinery has rich production experience and integrated service. Using our baler can greatly improve work efficiency and reduce human and financial expenditure. Contact us at 86-29-86031588 or https://www.nickbaler.net


    21-10-08
Contact Us
  • +86 29 86031588   (Fax)
  • 008615021631102
  • ligoodboy2010
  • sales@nkbaler.com
  • East Qunsheng Road Wuxi City,Jiangsu,China
Inquiry Us
Copyright © 2019 NICKBALER .rights reserved
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top