News Center
our commitment to nickbaler
  • When the vertical hydraulic Heavy Duty Baler is used for a long time,the battery may have some problems,so you must be cautious when using the battery of the vertical hydraulic Heavy Duty Baler.

    If you don't know this well,then,our Nick Machinery will share with you common knowledge about the battery usage of the vertical hydraulic Heavy Duty Baler

    I hope you can read it carefully and look forward to your attention.

    1.The new battery must be charged for 12 hours after the battery has cooled down 3 to 5 times before the battery is used up.Only after the first 3 to 5 times of repeated charging and discharging can the battery exert its normal larger power.

    2.The different voltage changes in various regions will affect the length of charging time.The high temperature of the battery or charger will reduce the charging efficiency and cause the battery to not be fully charged.Therefore,it is recommended that customers should charge in an environment of 10-40 degrees Celsius when charging,and install a regulated power supply before the charger.

    1.jpg

    3.To avoid short circuit of the battery,do not store it with metal objects.The positive and negative electrodes of the battery cannot be connected in any way.Do not open the battery case to keep the battery dry forever.

    4.When the machine is not in use,please remove the battery of the vertical hydraulic packer to avoid rapid power loss.A fully charged battery will lose its power completely after about 1 to 2 months.In order to extend the battery life of the automatic hydraulic Heavy Duty Baler,please install the removed battery on the machine to use up the remaining power,and confirm that the battery power is used up(red light is on) before charging.

    The above is the usage method of the vertical hydraulic Heavy Duty Baler battery,I hope it will be helpful to you.

    If you have more questions,please open our Nick Heavy Duty Baler company's website:www.nickbaler.net, or call:86-29-86031588


    20-10-09
  • Do you know how to deal with the downtime of the waste paper hydraulic baling machine during operation?

    1.Inspect the operation of the pump. If the small waste paper hydraulic baling machine is noisy,the needle swing is large,and the oil temperature is too high,the pump may be severely worn.

    2.Understand the operating efficiency of the pump.If the temperature difference between the pump casing and the fuel tank is higher than 5 degrees Celsius, the pump efficiency can be considered low.

    3.Check the oil leakage of the pump shaft and joints,and pay attention to leakage at high temperature and high pressure.

    4.Observe the indication value of the vacuum gauge installed at the suction pipe of the pump.During normal operation,its value should be below 127mmhg;otherwise,check the oil filter and working oil of the small waste paper hydraulic baling machine.

    废纸2.jpg

    5.There is air in the waste paper hydraulic baling machine oil,and air bubbles can be found in the oil tank.At this time,the oil is easily deteriorated and cannot be used.

    At the same time,the hydraulic system of the waste paper hydraulic baling machine equipment will experience vibration,noise,pressure fluctuations,unstable hydraulic components,crawling of moving parts,reversing impact,inaccurate positioning or disordered actions.

    In summary,please follow the operating procedure during the operation of the waste paper hydraulic baling machine to avoid damage to the machine and delay in production.

    The Nick brand waste paper hydraulic baling machine is easy to operate,high in safety,automatic out of the package, and more efficient. It is your best choice.


    20-09-25
  • An industry needs the help of another industry,and the development of an industry cannot take everything in.With the needs of people's material culture and modern products,the output of waste products is also increasing,and waste paper hydraulic baling machines are used in our daily lives.

    According to the current and future development situation,waste paper hydraulic baling machine equipment has broad market space and industry development prospects.

    20200916_140156_012.jpg20200916_140156_013.jpg

    With the continuous advancement of science and technology,the application of waste paper hydraulic baling machines in many industries has become more and more extensive.Many industries have used machinery to replace labor and improve production efficiency in order to reduce labor.The waste paper hydraulic baling machine is such a good equipment.

    Nick brand waste paper hydraulic baling machine is of reliable and guaranteed quality,sophisticated equipment and perfect after-sales service,which can better serve you.


    20-09-24
  • The automatic hydraulic baling machine is a machine specially used for the recycling and compression of waste paper,waste cardboard,carton factory scraps,waste books,waste magazines,plastic film,straw and other loose materials.What are the requirements for the use of oil in the hydraulic baling machine?

    1.In places where fire prevention is required,the ignition point of thick oil should be high;in places with cold climate,the freezing point of oil should be low.

    2.The oil should not be easily oxidized to avoid the occurrence of gum and asphaltene due to oxidation,which may cause the oil to degenerate.Impurities composed of oxides can also block the oil circuit and damage the normal operation of the hydraulic system.

    3.It has no effect on human health.

    废纸2.jpg

    4.Clean quality and no impurities.If there is moisture,it will reduce the smooth function of the straw hydraulic baling machine oil;mechanical impurities will block the throttle orifice and jam the valve core; acid and alkali will corrode the metal and damage the sealing structure;volatile substances will change the oil Thick and air bubbles occur,which damages the stability of the transmission.

    5.It has outstanding smooth function.In the hydraulic system of the hydraulic baling machine,the working fluid is not only used to transfer energy,but also has a smooth effect on the conflicting surfaces of the hydraulic components.

    The Nick brand automatic waste carton packing machine is easy to operate and automatically unpacks,which improves work efficiency.The installation of emergency stop settings makes the operation safer.


    20-09-23
  • The scrap metal hydraulic baling machine can squeeze various metal scraps,steel shavings,scrap steel,scrap iron,scrap copper,scrap aluminum,aluminum shavings,disintegrated car shells,waste oil drums and other metal raw materials into cuboids,cylinders,etc.The qualified charge of the shape is convenient for storage,transportation and recycling.

    Precautions for the new machine running-in period of the scrap metal hydraulic baling machine:

    1.Always keep the body of the scrap metal hydraulic baling machine clean,adjust and tighten loose parts in time to prevent the loose parts from aggravating the wear of the parts or causing the loss of the parts.

    2.Before using the new waste paper hydraulic baling machine,pay attention to checking the lubricating oil,hydraulic oil,coolant,brake fluid and fuel oil(water)level,and pay attention to checking the tightness of the waste metal hydraulic baling machine.

    金属20.jpg

    At the same time,the lubrication of each lubrication point should be strengthened.It is recommended to add grease to the lubrication point during the running-in period.

    3.Pay attention to frequently check the various instruments of the scrap metal hydraulic baling machine equipment.If there is an abnormality,stop it in time to eliminate it.

    4.Pay attention to the workload during the running-in period.The workload during the running-in period should generally not exceed 80% of the rated workload,and appropriate workloads should be deployed to prevent overheating caused by long-term continuous operation of the machine.

    Nick brand metal hydraulic baling machine is easy to operate,safe and energy-saving,it is your best helper.


    20-09-22
  • The waste paper hydraulic baling machine has a wide range of uses.It can pack loose items such as waste paper,waste paper boxes,straw,straw,etc.,to facilitate transportation and save space,making it an indispensable equipment for many industries.

    So do you know the reason for the heating of the hydraulic oil of the waste paper hydraulic baling machine?Today Nick Machinery will give you an explanation.

    1.The accuracy of the components and the quality of the equipment are poor.The mechanical conflict between relative motions is too large,the planned structure of the hydraulic components in the system is unreasonable,and the production quality is poor.

    The unloading circuit in the system is faulty.Perhaps because the unloading circuit is not set,the oil pump cannot unload when the operation is stopped.The entire flow of the pump overflows under high pressure,and the overflow rate generates heat,which causes the oil to heat up.

    13.jpg

    2.Select the fixed pump oil supply system of the oil pump capacity according to the fast forward speed.During operation,most of the remaining flow will overflow from the overflow valve under high pressure and generate heat.The standard selection of hydraulic components in the hydraulic system is unreasonable.

    If the standard is too small,the formation energy will lose too much and cause the system to heat up,or the flow rate will be too high and cause noise.When the pump flow is too large when the pump is selected,the remaining oil will overflow from the overflow valve and cause heat.

    It is recommended that you choose high-quality equipment,so as to improve production and better serve you.Recommended here is Nick Machinery's waste paper hydraulic baling machine,which is of good quality,good quality,simple structure and easy to operate.


    20-09-21
Contact Us
  • +86 29 86031588   (Fax)
  • 008615021631102
  • ligoodboy2010
  • sales@nkbaler.com
  • East Qunsheng Road Wuxi City,Jiangsu,China
Inquiry Us
Copyright © 2019 NICKBALER .rights reserved
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top