News Center
our commitment to nickbaler
Position:Home > News Center <<    Return
Drawings of horizontal waste paper baler
Author : admin Time : 20-05-31 AllPageView : 215

The horizontal waste paper packing machine is composed of seven parts: framework, box, hydraulic control system, main oil cylinder, oil supply system, electrical control system, hydraulic oil cylinder and hydraulic lock box door.

1. Rack

The frame is composed of a vertical pole, a lower beam, a middle beam and a top beam. The upper end and the lower side beam are connected to support all the racks with supporting points and bear complicated loads. Therefore, select high-quality stainless steel plates to ensure sufficient compressive strength.

2. Frame

The box is divided into 1 box and 1 shrink box. The door is connected by a locking cylinder, a door hinge uranium and other components. Lock the barrel to lock the door and loosen it to facilitate the door opening and closing. The negative part is placed under the gift box. The wooden floor is made of carbon steel plate, and the packaging of soldering iron and thin iron wire is convenient.

3. Hydraulic control system

The system is composed of fuel tank, gear pump (80 type) electric pump set, hydraulic multi-way valve, oil delivery pipe, and cylinder. Gear oil around 46 # must be applied. The system and electronic device components cooperate with each other, and can manipulate individual behaviors in every job of the waste paper packer.

4. Master cylinder

The main engine cylinder plug has a diameter of 160MM and its cross-section is 251CM2. The total working pressure of the waste paper packer is 800KN. The limit switch limits the lift of the plunger pump. The main cylinder system is composed of the main engine block, plunger pump, sealing ring, guide ring, top block, etc., with excellent sealing characteristics.

微信图片_20200511095153.jpg

The plunger pump and the seamless pipe in the cylinder are welded and welded together, which has sufficient compressive strength. The plunger pump makes repeated movements in the cylinder. When the plunger pump rises, the force is transmitted to the top block in the small box, and the block in the small box is reduced.

5. Key oil supply system

This system is the energy source for the waste paper packer. Its advantages and disadvantages are particularly important for waste paper packers. Therefore, high-quality gear oil beyond 46 # must be applied. The system is composed of diesel fuel tank, 11KW motor, 80-type piston rod gasoline pump, ZS1 series hydraulic directional valve, speed regulating valve, unloading valve and filtering device.

6. Part of the electrical control system

The machine's main switching power supply is three-phase 380V 50Hz AC current. The cross section of the output power electric conductor shall not be less than 16mm2 (copper).

7. Working pressure cylinder

The effect of these is to feed raw materials into compression bags and preload them. Working pressure 20-25 MPA. The journey is 2700 MM.


Recommended news
  • The impact of environmental awareness on waste paper baler

    With the increasing use of waste paper baler machinery, the frequency of use has gradually increased. However, there are still some people who may not know the waste paper baler very well. Some people even think that the waste paper baler is a waste paper recycling machine. Some people even think that it is the evolution of the waste paper basket. In fact, this is not the case. The waste paper baler is actually an existence for more convenient recycling of waste paper. The waste paper baler can compress and integrate waste paper to facilitate recycling and transportation.

    People's awareness of environmental protection is getting stronger and stronger, and environmental problems are becoming more and more serious. Every one of us citizens should fulfill their environmental protection obligations and contribute to environmental protection. Therefore, under the background of environmental protection, the waste paper baler came into being and was well received. Our waste paper packaging technology is not particularly perfect, but we are also following in the footsteps of foreign advanced technology, and we are constantly innovating and improving. 

    8-2废纸.jpg

    The waste paper baler can pack some waste paper for recycling and reuse, which is mainly suitable for some large paper mills or large users of paper products. And the waste paper baler can also recycle old things such as plastic straws.

    The application of waste paper baler greatly reduces the loss of manpower and material resources, and is convenient and fast, simple to use, and large-area waste paper baling and recycling is of great significance to environmental protection and avoiding waste.

    NICKBALER waste paper baler can be designed and customized according to the actual site of the customer. www.nickbaler.net

  • The influence of hydraulic system on waste paper baler

    The cleaning operation of the hydraulic system inside the waste paper baler is very important to the baler, because the waste paper baler needs a good hydraulic system when working. Therefore, in daily work, the cleaning of the baler should not be underestimated and must be taken seriously. Below, let's take a look at the precautions for cleaning the waste paper baler:

    When cleaning the waste paper baler, a low-viscosity special cleaning oil should be used. The clean oil is added to the fuel tank of the waste paper baler and heated to 50-80 degrees Celsius. Start the hydraulic pump and let it run dry. When cleaning the baler, you must often knock on the tube. This can remove the attachments. Clean for about 20 minutes. Check the contamination status of the oil filter, and clean the filter, and then clean it again. Repeat until there are not many contaminants on the filter. It’s okay when it’s time.

    The cleaning time of waste paper baler is generally 2 hours. For the more messy hydraulic system, each area can be cleaned according to the work area. The hydraulic cylinder can also be connected to allow the hydraulic cylinder to reciprocate to clean the system.

    7-2废纸.jpg

    After cleaning, the clean oil must be drained, and the inside of the oil tank must be cleaned. When the waste paper baler system is restored to the normal operating state, add the specified hydraulic oil.

    Nick Machinery's waste paper baler has the characteristics of easy installation and operation, safe and reliable use, strong adaptability to the workplace, and reasonable price. www.nickbaler.net

  • Technological innovation is the top priority for the development of waste paper baler

    After years of development, waste paper baler has formed a considerable scale, although the scale of development of my country's baler industry has been very large. Nowadays, the development of all walks of life is inseparable from innovation. If the vertical waste paper baler can be developed in terms of technological innovation, at the same time in response to the call of the country, it will also bring more economy to the vertical waste paper baler equipment enterprises. interest.

    The new technology of vertical waste paper baler can increase the output of equipment. Although my country's waste paper baler industry has developed so fast in the past two years and the export volume has increased significantly, it is undeniable that there are still many shortcomings in the vertical waste paper baler

    If these problems are not improved in a short time, it will inevitably affect the development of the baler industry and the position of the vertical waste paper baler in the baler industry. The concentration of my country's baler industry is not enough, production capacity is scattered, and economies of scale cannot be formed. At present, the production capacity of the vertical waste paper baler has developed rapidly, but the technological progress of the industry is relatively slow, and the R&D and innovation capabilities are low. The service life and reliability of the vertical waste paper baler have gradually been unable to meet the needs of technological development. Therefore, technological innovation is urgently needed.

    The vertical waste paper baler is currently still stuck on capacity expansion, which makes China's baler industry lack a certain brand effect. Therefore, in terms of technological innovation of vertical waste paper baler, we must increase efforts to make contributions to my country's baler industry.

    6-2废纸.jpg

    The quality of the vertical waste paper baler is inseparable from the oil cylinder, and the function of the oil cylinder determines the stability of the baler. Similarly, the quality of hydraulic oil also affects the failure rate and service life of the cylinder. The cylinder needs to use No. 46 anti-wear hydraulic oil to ensure the efficient production of the baler.

    In the current baler industry, many small manufacturers are reluctant to develop and research new products, and will blindly imitate the products of large baler manufacturers. This is also an important factor leading to the slow development of the waste paper baler market.

    With the management philosophy of "Integrity creates the brand, and quality determines the future", Nick Machinery continues to improve the mechanism, strengthen brand awareness, and make products with excellent quality and better after-sales service. www.nickbaler.net


Recommended products
  • NK8060T15 Diesel Engine Baler
  • Wood Shaving Bedding Machine
  • PET Bottle Baling Press Nick Baler
  • Automatic Waste Paper Box Baler
Recommended Assorises
  • Sack for Used Clothes Packing
  • Semi automatic Strapping Machine
  • Wooden Crusher /Wooden Shredder
  • Hydraulic Forklift Truck
  • Strapping Baling Wire for Baler
  • Pipe Shredder with Hydraulic Balers
Contact Us
  • +86 29 86031588   (Fax)
  • 008615021631102
  • ligoodboy2010
  • sales@nkbaler.com
  • East Qunsheng Road Wuxi City,Jiangsu,China
Inquiry Us
Copyright © 2019 NICKBALER .rights reserved
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top