News Center

our commitment to nickbaler
Position:Home > News Center <<    Return
How to regulate the operation of waste paper hydraulic balers
Author : admin Time : 20-02-06 AllPageView : 4713

With the use of waste paper hydraulic balers more and more enterprises, waste paper hydraulic baler operation norms have become more and more people concerned about the problem. This is related to the safety of the enterprise and the workers themselves


1, the use of waste paper baler before the operation should be strictly in accordance with the company system to wear uniforms, fasten the cuffs, buckle a good button, control waste paper baler to bring the clothes into the machine caused by the accident.

2, the packer operator should be in the job before the training, familiar with the waste paper baler of the various parts of the structure, performance and use methods!

3, packer before the operation, should clean up the site health, and clear automatic paper baler equipment on the oil and debris and so on.

4, baler in the maintenance and maintenance of the time should be carried out in the case of power failure, and prohibit the collision start button and handle!

5, before the use of balers, air idle inspection work to check whether there is noise, tank level is sufficient, whether the loose parts of the phenomenon!

6, balers in the work is strictly prohibited limbs into the work of the device parts, so as not to cause harm to the human body!

7, is strictly prohibited free demolition of all parts of the baler parts, if the equipment failure should be timely contact with professional maintenance personnel to remove the fault!

Recommended news
  • Process 10 tons of waste paper balers per day?

    How to choose the type to process 10 tons of waste paper every day?

    First of all, NICKBALER suggests that if the daily processing capacity reaches 10 tons, you can choose a horizontal baler, and the horizontal baler is divided into: semi-automatic baler and full-automatic baler; if the initial investment is limited, you can use the semi-automatic baler. Choose from the baler, and the smallest model NKW60BD can meet the production requirements;

    If you have a spacious site and sufficient funds, and have better development and planning in the future,NICKBALER suggests that you can choose a fully automatic baler; what is the difference between a semi-automatic baler and a fully automatic baler?

    1. The architecture is different

    2. Different packing methods

    3. The output is different

    NKW 250Q 01.jpg

    Waste paper baler is our main product for many years, we have very valuable experience, if you want to know more, please follow us https://www.nickbaler.net


  • How to clean the hydraulic system of the baler in the Philippines?

    1. String the baling pressrope of the hydraulic baler through the automatic spring tightening device behind the garbage compressor, and place it along the baling pressbelt groove, then tie the baling press belt to the pull-stop at the bottom of the baling pressgroove, and rotate the automatic spring tightening device 90 degrees , close the bottom door and lock

    2. Put the recycled waste paper, plastic and film waste into the hydraulic baler. When the material is loaded to the height of the pressure plate, close the door tightly and press the "press down" button. The equipment runs automatically and compacts. (The feeding height of materials other than cardboard can only be slightly higher than the bottom door)

    3. The pressure plate moves down and compresses to the maximum pressure and automatically returns to the fully open position. When compressing the baling pressconstraints, the platen stops at the preset position of the compressed material

    4. Open the door of the device and pass the tie rope through the bottom wire groove from front to back and back to the front through the pressure plate wire groove. Tighten the tie rope by hand and tie a knot. Push the baling press rod by hand, push the rod to a fixed position, and clamp it tightly. Press the "Up" button, the return trip of the oil cylinder will automatically turn out the bundled bundles. (When opening the lower door, it is not allowed to go in front of the door。

    Stand up to avoid accidental injury from the door popping open)

    5. After the bale is ejected, reset the bale rod to press down. Finally, remove the bales of waste paper and plastic waste before stacking them for storage, close and lock the door and enter the next packaging cycle task

    NKW250Q 02.jpg

    The hydraulic baler produced by NICKBALER has a simple structure, stable operation, low failure rate and easy cleaning and maintenance. You are welcome to buy https://www.nickbaler.net


  • Daily maintenance of automatic hydraulic balers in India

    1. Before starting the machine, check whether the components of the baler are in good condition; whether the screws and nuts of each component are loose, if so, you need to tighten the screws and nuts, repair personnel to deal with.

    2. Check whether there is any debris blockage inside the machine. The debris blockage will affect the work of the automatic hydraulic baler, so it needs to be removed;

    3. Check whether the knife group and the sliding part are short of oil. If the oil is short, it will cause serious wear on the parts. It must be oiled by dipping and dripping. Use a small stick to dip the oil and slowly drip it on it.

    牛粪01.jpg

    For more information on the fault maintenance and maintenance work of the automatic hydraulic baler, please pay attention to the website of NICKBALER Machinery Company: https://www.nickbaler.net


Recommended products
  • RDF baler's maintance
  • MSW Vertical Baler Machine
  • MSW Environmental protection equipment
  • MSW Horizontal Hydraulic baler machine
Recommended Assorises
  • Cyclone Separator
  • Diesel engine generator
  • Forklift Car
  • Wire Buckle For Baling
  • Iron Wire For Baling
  • Ton Bags/Jumbo Bag

Contact Us

  • +86 29 86031588   (Fax)
  • 008615021631102
  • ligoodboy2010
  • info@nkbaler.com
  • East Qunsheng Road Wuxi City,Jiangsu,China

Inquiry Us

Copyright © 2019 NICKBALER .rights reserved sitemap.html
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top