The fully automatic horizontal waste paper Baling Machine is a well-conceived machine, and small motors have also received attention. Therefore, be careful when buying a horizontal waste paper Baling Machine. The electric motor used in the hydraulic horizontal baler includes two parts, a stator and a rotor. The stator of the motor of the horizontal waste paper baler is also called an armature, and includes a base, an end cover, an armature core, an armature winding device, and the like.
The electromechanical pivot core packaged by the fully automatic horizontal waste paper baler is installed on the inner circumference of the machine base, which is the support of the generator and is made of cast iron. Install the end caps at the ends of both ends. The lifting eye is used for lifting. The round hole of the calf is used to install the bolt. The ground bolt on the base is used to install the ground wire. In order to dissipate and maintain the hydraulic baler motor, ventilation windows are left on the end caps, and shutters are used to prevent debris from entering.
The rotor includes the rotor core, rotor (excitation) winding, fan, rotating shaft, etc. The rotor core is the winding part of the horizontal waste paper baler motor and is made of 1-2M thick steel / laminate. The core is bolted to the yoke, which is made of a single piece of low carbon and placed on the uranium through a steel truss.
When we use a fully automatic horizontal waste paper Baling Machine, the verification method to diagnose and deal with the fault is to find out whether the equipment can operate normally, so as to ensure the normal and stable operation of the automatic hydraulic horizontal waste paper Baling Machine during operation The technical means of the entire equipment also restricted or promoted practical work.
Nick Baler can supply many kinds of baler machine,Waste paper baler machine,For more information ,please visit : www.nickbaler.net or www.nkbaler.com .even you can send us whatsAPP:00 86 15021631102 to free talk and inquiry as any time
1. The equipment should be operated by human beings, and others are not allowed to use it arbitrarily without training.
2. Before driving, check whether all parts are normal and whether the fasteners are firm.
3. It is prohibited to cut unannealed steel parts, cast iron parts, soft metal parts, over-thin parts, parts less than 100 mm in length, and parts that exceed the length of the scissors.
4. During operation, the human body is forbidden to be close to the transmission part and the knife edge of the equipment, and the safety of the surrounding personnel should be paid attention to to prevent the material from lifting up and hurting people. When cutting, the material should be cut as close as possible to the inside of the knife. When cutting shorter materials, do not use hand-held workpieces to feed materials, and use clamps to feed materials.
5. When the equipment is running, the operator is not allowed to leave the post privately, and the power supply should be blocked when the operation is over or temporarily leaving the post.
Nick machinery does not need to install anchor screws, in places where there is no power supply can use diesel engines as power. For more information, contact 86-29-86031588
This series of equipment is classified into two types: vertical type and horizontal type.
Components:
This series of equipment is mainly composed of the following components:
①Main machine: It is composed of frame, main hydraulic cylinder, pusher hydraulic cylinder, bottom hydraulic cylinder, matching mold frame and mold, and indenter number.
The frame part is composed of upper and lower beams and uprights. The upper and lower beams are all made of all cast steel parts. The upper and lower beams are connected by inner and outer nuts with four columns to withstand the tension during operation.
The main hydraulic cylinder eliminates steel castings and eliminates safety hazards. Ensure the service life and operational safety of the equipment. Supporting mold frames and molds, the top number of indenters, through professional planning, cooperation, and superior processing capabilities are the guarantee for an outstanding taste of the equipment.
②Hydraulic station: It is composed of motor, hydraulic pump, pump protection device, professional control valve block and piping system for connecting briquetting machine. The planning is reasonable and the quality is stable. Equipped with a cooling system to prevent the equipment from being unable to operate continuously due to overheating of the oil.
③Console: It is composed of electrical system and plc control system.
Equipped with an adjustable text display, the sequence of actions and each action moment are completely controlled by the PLC system, and can be adjusted by the operator at any time, which is convenient and quick, simple and easy to understand.
Nick Machinery's metal baler is mainly suitable for steel mills, recycling and processing industries and non-ferrous and ferrous metal smelting industries. Contact consultation telephone 86-29-86031588
The mechanical processing method is to use special scrap steel processing machinery to process the scrap steel, to achieve the purpose of improving the quality of the scrap steel, which is conducive to the tempering of the furnace and the convenience of transportation.
There are many types of scrap steel processing machinery, and users can choose appropriate scrap steel processing equipment according to the processing requirements of scrap steel and the scale of production and economic capacity of the enterprise.
At that time, scrap steel processing equipment was divided into processing and auxiliary feeding equipment. Processing methods include Baler, briquetting, cutting, crushing, etc.
1. Mechanical packaging method
The mechanical baling method is to use a metal baler at room temperature to limit the frivolous steel scrap into bales with a certain shape and density. This kind of bale can be exercised in the furnace, and it is also easy to transport, which saves transportation capacity and reduces environmental pollution during transportation. The equipment used is a metal baler.
2. Mechanical briquetting method
Many metal cutting processes in the production process of the machinery industry produce a lot of steel chips, cast iron chips, copper chips, aluminum chips and other chips. If these chips are discarded, it will not only waste resources, but also severely pollute the environment. Taking it back and returning it to the oven after processing is a useful way to deal with it.
The processing equipment for metal chips is a metal chip briquetting machine, whose processing method is to directly limit cast iron chips, copper chips, and aluminum chips into a cylinder with a higher density at room temperature. If it is a long strip of steel shavings, the steel shavings should be broken before the restriction, and then restricted.
The scrap steel briquettes processed by the briquetting machine generally have a density of more than 4500kg/m3, which greatly reduces the volume of the scraps, improves the transportation capacity and can be returned to the furnace for exercise, and can also reduce the environmental pollution during transportation. The equipment used is: Metal briquetting machine.
3. Mechanical shearing method
The so-called shearing is to use a scrap shearing machine to cut the long strip of steel scrap to a suitable length for training. Nowadays, the scrap steel shearing machine has three types of structure: crocodile type, double-edged crocodile type and portal type. The equipment used is: metal shearing Machine, box-type shearing machine, heavy-duty shearing machine, etc.
Nick Machinery's automatic hydraulic baler is an unmanned operation of fully automatic compression and Baler, suitable for places with a lot of materials, reducing labor expenditures and improving work efficiency. https://www.nickbaler.net
