News Center

our commitment to nickbaler
Position:Home > News Center <<    Return
Reasons for hydraulic oil heating of hydraulic straw baler
Author : admin Time : 20-05-31 AllPageView : 498

1. Insufficient component accuracy and poor assembly quality, large mechanical friction loss between relative movements, unreasonable design structure of hydraulic components in the system, and poor manufacturing quality. After the oil passes through the valve, the pressure loss is large and the internal leakage is serious.

2. The quantitative pump oil supply system that selects the capacity of the oil pump according to the fast forward speed. During operation, most of the excess flow will overflow from the overflow valve under high pressure and become heated. The selection of hydraulic components in the hydraulic system is unreasonable. When the valve is selected, due to too small specifications, the energy loss is too large and the system heats up, or the internal tassel is too high and causes noise. When the pump is used, the flow of the pump is too large, then excess oil will overflow from the overflow valve and cause heat.

3. The unloading circuit in the system is faulty or because the unloading circuit is not installed, the oil pump cannot be unloaded when the work is stopped. All the flow of the pump overflows under high pressure, causing overflow loss and heating, resulting in oil heating.

4. The system pipeline is too thin and too long, too much bending, local pressure loss and large pressure loss along the way, there are extra hydraulic circuits or extra hydraulic components in the hydraulic system.

5. The volume of the oil tank is too small, the heat dissipation area is not enough, no oil cooling device is installed, or the capacity is too small although there is a cooling device.

6. The clearance of the matching parts is too small, or the wear will cause the clearance to be too large, and the internal and external leakage will be large, resulting in a large volume loss, such as a reduction in the volumetric efficiency of the pump and rapid heat generation.

7. The working pressure of the hydraulic system is adjusted higher than the actual needs. Sometimes it is necessary to increase the pressure to work because the seal is too tight, or because the seal is damaged and the leakage increases.

8. The viscosity of the selected oil is improper, the viscosity is large, the viscosity resistance is large, and the viscosity is too small, the leakage increases, both cases can cause the oil to heat up.


Nick Baler can supply many kinds of baler machine,Waste paper baler machine,For more information ,please visit : www.nickbaler.net or www.nkbaler.com .even you can send us whatsAPP:00 86 15021631102 to free talk and inquiry as any time


Recommended news
  • Features of MSW Baling Press Machine

    1. The structure of the hydraulic MSW horizontal baler is mainly closed-door and open-door structure. The closed-door structure can make the density of the bales larger, which is suitable for the compression and baling machine of more items, hydraulic opening and closing, manual bundling, safe and fast operation.Open door structure, both sides are locked, continuous delivery, automatic threading (wire) or hooking (wire), automatic bundling, and faster operation.

    2. Imported PLC programming, LCD screen, simple, clear and clear at a glance.

    3. The connection method of the ball joint hydraulic cylinder is not prone to failure and increases the use time of the cylinder.

    4. Thickened steel plate, the fuselage is firmer.

    5. The oil circuit is standardized, and the hydraulic oil pipe hose is rarely used, which avoids the oil leakage phenomenon caused by the loosening of the screw due to the vibration of the machine, and also reduces the potential safety hazard.

    6. A variety of operation methods.

    7. Energy saving, low noise.

    mmexport1560419350147 拷贝.png

    All of NICKBALER Machinery's balers can do the job you need and are very easy to operate. If you have any questions, you can go to NICKBALER's website to learn.https://www.nickbaler.net.


  • NK-T90L Double Chambers Clothes Balers

    NK-T90L double-chamber Clothes baler The double-chamber clothes baler is used for the compression and Baling Machine of old clothes, towels, rags, fabrics and other materials.

    It is also known as an open double-chamber baler, a rotatable dual-chamber baler, or a two-case baler. This baler is designed with two compression chambers. The two compression chambers are rotated and balanced by a central shaft. The double cavity can realize feeding in one cavity and compressing the bale in the other cavity, which greatly improves the work efficiency. When the block is compressed,the cavity will have a signal to automatically carry the box, so that it can be easily bundled. This double-chamber clothes baler combines the dual advantages of the double-chamber baler and the suitcase baler, and is currently the most efficient, user-friendly and labor-saving garment baler in the industry.

    cc561b38ee076be9aa635a9ef866467 拷贝.png

    The double-chamber clothes baler produced by NICKBALER has always had its own uniqueness, because we believe that only by making our products more refined and more distinctive, our sales will be broader. If necessary, feel free to contact us at 86-29-86031588


  • Features of foam Baling machine

    The Baling Machine generally consists of five parts: the pressing part, the crushing part, the electrical control part, the pressure control part and the power part. So what are its characteristics? Let's find out

    1. The compression ratio is large, and the maximum capacity can be reduced by 50 times.

    2. Save storage space, save transportation and storage costs

    3. The compressed PS material is easy to recycle

    4. Large-scale models can operate synchronously with the conveyor belt to improve production efficiency

    mmexport1562302687362.jpg

    Foam Baling Machine is our main product for many years, we have very valuable experience, if you want to know more, about us https://www.nickbaler.net


Recommended products
  • MSW Environmental protection equipment
  • MSW Horizontal Hydraulic baler machine
  • Waste paper baling machine with manufacturer price
  • Manufacturer supply scrap paper baling machine
Recommended Assorises
  • Cyclone Separator
  • Diesel engine generator
  • Forklift Car
  • Wire Buckle For Baling
  • Iron Wire For Baling
  • Ton Bags/Jumbo Bag

Contact Us

  • +86 29 86031588   (Fax)
  • 008615021631102
  • ligoodboy2010
  • Tony.wang@nkbaler.com
  • East Qunsheng Road Wuxi City,Jiangsu,China

Inquiry Us

Copyright © 2019 NICKBALER .rights reserved sitemap.html
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top