The waste paper Baling Press has the characteristics of good rigidity, good stability, beautiful appearance, convenient operation and maintenance, and low investment cost of basic equipment. Widely used in various types of waste paper mills, waste materials recycling companies and other units. It is suitable for recycling of waste paper and plastic straws. It is a good equipment for improving labor efficiency, reducing labor intensity, saving manpower and reducing transportation costs. The use range of the waste paper Baling Press is very wide, but the maintenance is not in place, there will be some small faults, which will affect the packaging process, often, and there is a lot of noise. So, what are the commonly used maintenance methods for waste paper Baling Presss? Below, I will introduce the use and maintenance methods of the waste paper Baling Press:
The maintenance of the waste paper baler often determines the service life of the machine itself and the operation efficiency of the machine. The waste paper baler itself is actually classified as a high machine type. The machine's process requirements are very high, and its structural parts are strictly In order to conduct mass production through inspection, internal irregularities will often cause problems and problems in the waste paper Baling Press.
What should I do if there is a line failure during use of the waste paper Baling Press?
1. Electrical circuit failure
(1) The electrical circuit of the waste paper Baling Press is broken, the electromagnet is not energized, and there is no control signal to replace the wire, so that the electromagnet is energized.
(2) The electrode is poorly welded, the joint is loose and re-welded, and the joint is welded.
(3) The voltage is too low or unstable. Check the voltage at both ends of the electromagnet. The change value should be within 10 of the rated voltage.
2. The solenoid coil heats up to burn
(1) The insulation of the coil is poor, and the leakage occurs and the coil is replaced.
(2) The electromagnet core is not qualified and cannot replace the electromagnet core.
(3) The push rod is too long, the electromagnet core cannot be sucked in place and the push rod is trimmed to a proper position.
(4) The electromagnet works at high frequency, the core dry friction causes heat expansion, the core is stuck to repair or replace the core
Nick Baler has several type of recycling Baler baling equipment for choice. Heavy duty baling and horizontal baler machine, vertical baling and paper baling press machine, cardboard paper baler,welcome to contact us.
With the development of the economy and the continuous innovation of science and technology, more and more people are now paying attention to environmental protection, and environmental issues have also attracted attention, making the straw baler more popular, and its advantages are becoming more and more prominent. What are the advantages of the straw baler? ? Please see the analysis below
1. It is very versatile, mainly for packing some large or loose items.
2. Save storage space and recycle waste items.
3. The parts of the straw baler have high structural performance and good work efficiency, which reduces labor and transportation costs.
Only a high-quality baler can be better trusted by customers, and only by understanding the performance of the baler, can the straw baler be better utilized and used. Follow NICKBALER, let you grow more https://www.nickbaler.net
Choosing NICKBALER hydraulic baler, independent hydraulic system and servo system control, is the best choice for you to solve and recycle waste. https://www.nickbaler.net
The straw baler must be inspected and maintained at ordinary times to ensure that it can operate normally. While ensuring the characteristics and working efficiency of the straw baler, the following 4 points must be done:
1. Check the screws of each component of the straw baler on time to prevent falling off or bursting;
2. Pay attention to the moisture-proof, waterproof, anti-corrosion and fly-proof of some electrical equipment. The interior of the electrical control cabinet and the terminal block must be kept clean to prevent common failures of electrical equipment;
3. The machine of the straw baler is broken. The two heat-sealing rollers should be in the extended position to prevent the baling machine products from being scalded.
4. Lubricate the junction of each transmission gear, the oil filling hole of the bearing with seat and the oil pump of each movable component of the straw baler on time.
5. When the straw baler is filled with grease, it is not necessary to drop droplets on the transmission belt of the transmission system to prevent damage caused by deviation and vibration or aging of the transmission belt.
For more information about the fault maintenance and maintenance work of the straw baler, please pay attention to the website of NICKBALER M: https://www.nickbaler.net
1. The operator should be strictly trained and qualified before using the machine.
2. When the ambient temperature is less than 2°C above zero, the straw baler is not allowed to be used.
3. When the moisture content of straw and pasture is more than 65%, the straw baler is not allowed to be used.
4. The operator is not allowed to pour liquids such as bacteria water on the baler while bundling.
5. The straw baler is not allowed to have 2 boring cars per hour.
6. When using the motor as power, it is necessary to install the grounding wire.
7. It is necessary to clean up the small silt under the straw baler in time. If there are too many scraps, it may damage the machine parts.
If you are still unclear, you can continue to pay attention to our website https://www.nickbaler.net, and you are welcome to contact us at any time , thank you for reading.
