If the horizontal waste paper baler is too loose or too tight when packing items, it needs customer's attention. This will not only affect the neatness and deformation of the appearance of the item, but also directly affect it. Subsequent sales will greatly discount your product image, which is very cost-effective. So, how to adjust the tightness of the horizontal waste paper Baling Press?
If it is a semi-automatic horizontal waste paper Baling Press, you need to turn off the power first, the cover is opened, you have found that on your right hand side is a rear, there is a big spring held up by a nut, manual only need to adjust this nut That's it, mainly the pressure of the nut on the spring. If the nut is turned clockwise, the pressure on the spring will be reduced and the baler will be looser. Conversely, if it is adjusted counterclockwise, the baler will be more tightly packed.
Although the semi-automatic horizontal waste paper baler and the fully automatic horizontal waste paper baler are both functions of packing, there are still certain differences.
Factors affecting the production efficiency of waste paper baler
The most direct factor affecting the production efficiency of the waste paper baler is the model specifications of the baler. The production efficiency of the conventional baler is higher than that of the baler with a door at the discharge port. ?
The high-efficiency production capacity of the waste paper baler is inseparable from the performance of the baler's oil cylinder. The performance of the oil cylinder also determines the stability of the baler. To ensure the efficient work of the baler, it is necessary to select a baler manufacturer with superb production technology.
With the continuous innovation of my country's science and technology, all aspects of technology have been recognized by all parties. In the current society, from the construction site to the fully automatic unmanned waste paper Baling Press, it has already been an extreme cash withdrawal and development.
1. Shearing oil cylinder: It is a double-acting single-piston rod type oil cylinder. Its front end is connected with the frame, and the rear part is connected with the machine base by lower pins (one on each side), and the frame shaft is driven by the push-out and retraction of the piston rod. swing. Implement the cutting action.
2 Frames: The frame is an important flowing part. The left side of the front part is equipped with an upper shear. The middle is connected with the frame by the frame shaft and frame bushing, and the rear is connected with the upper pin shaft of the shear cylinder. .
3. Machine base: It is composed of welding base, left frame, right frame, etc. The right frame and the left frame of the base are welded parts, of which the right and left frames use inner and outer (double) side plates, and the structure is firm.
4. There is a platform and a slope at the front of the machine base, and a lower shear is installed between them. There is a large hole in the middle of the left and right frames for installing the frame, and there is a hole in the rear for installing the shearing cylinder. The front part of the frame is welded with a pressure material cylinder bracket, which is used to install the pressure material cylinder and other portal metal shears.
NICKBALER has rich production experience and integrated services. Using our balers can greatly improve work efficiency and reduce human and financial expenditures. Contact us at 86-29-86031588 or https://www.nkbaler.net/.
The semi-automatic plastic bottle Baling machine is mainly used for Baling machinewaste products, but because it is semi-automatic packing, it needs to be worn manually. Many friends do not know how to operate it. NKBALER has summarized the following points based on experience , I hope it can help everyone.
Semi-automatic plastic bottle Baling machine strapping method:
1. Install the pp tape on the pp tape mounting roller.
2. There is a brake pad connected to the "L"-shaped metal rod on the roller and the fuselage. There are two white rollers on the metal rod. middle.
3. After the upper and lower extensions are inserted, press the connecting spring on the front of the upper extension (the machine is turned on at this time).Line packing.
The above is the method of wearing the semi-automatic plastic bottle baler. I believe that through the introduction, everyone has a deeper understanding of how to operate the plastic baler. If you have other questions, you can leave a message for consultation.https://www.nkbaler.net/.
The electrical control part of the waste paper baler is mainly composed of PLC, motor and electrical components of relays and switches. The most vulnerable parts of these parts are the motor and electrical components. Today we share with you: baler electrical control Box Daily Precautions
1. Pay attention to the grounding, lightning protection, rainproof and moisture-proof of the power cord.
2. Non-professional operators of the electric control cabinet are prohibited from using it.
3. Pay attention to the antifreeze work of the motor and the long-term overload of the motor. Effective prevention of these two items can greatly reduce the damage to the motor, thereby maintaining the normal Baling machineof the waste paper baler.
4. Pay attention to the button operation of the console part, do not use too much force on the switch button, and prevent misoperation to avoid damage caused by short circuit.
The above 4 points are what I want to share with you today, I hope it can help you!
NKBALER provides: horizontal hydraulic baler, vertical hydraulic baler, waste paper baler and other Baling machineequipment, company website: https://www.nkbaler.net/. Tel: 86-29-86031588, looking forward to contacting your cooperation!
