The waste paper Baling Press is a packing machine used to compress waste paper items. It is used by various types of waste paper mills, old waste recycling companies and other units for the compression of various recyclable fluffy waste products such as domestic waste, industrial waste, plastics, films, pasture, straw, cotton, iron scrap, aluminum scrap, and scrap. Bale.
In general, what environment will cause damage to the baler?
Corrosive environment. This environment is mainly manifested as strong acids or bases. Because the shell of carbon steel is not as corrosion-resistant as stainless steel, the shell is easily corroded in such an environment.
Severely humid environment. Many factories producing aquatic products have relatively high air humidity and even deep water on the ground. At this time, it is obviously inappropriate to use an ordinary semi-automatic baler. The first is that the machine itself will be easily damaged, and the second is that the baling belt is returning. At this time, the strap will fall on the ground and get wet, and it will be very uncomfortable when you work again.
Packing machine use characteristics
1. It has the characteristics of small volume, light weight, low motion inertia, low noise, smooth movement and flexible operation.
2. It has a wide range of applications. It can be used as a packaging device for waste paper and as a processing device for packaging and compacting similar products.
3. PLC control, with man-machine interface (touch screen) and inspection-type monitoring, synchronous action indicator map with error warning, the length of the packet can be set.
4. The design of floating shrinkage in three directions of left, right and upper is conducive to automatic distribution of pressure on all four sides and can be widely used for packaging different materials.
5. Automatic strapping to improve the packing speed.
6. The push cylinder and push head are connected by a spherical structure, with good reliability and long service life of the oil seal. ?
7. The feeding port is provided with a dispersing shearing knife, which has high shearing efficiency.
8. Low noise hydraulic circuit design, high efficiency and low failure.
9. Easy to install without foundation.
10. Horizontal structure, can be equipped with conveyor belt feeding or manual feeding. Product introduction of waste paper Baling Press
In general, what are the marketing strategies for waste paper Baling Presss?
1. You must have sufficient analytical capabilities, including the sales data of small waste paper Baling Presss and other products in the past. You must analyze the market development trends in a timely manner, and then formulate a complete series of production and sales plans, that is to say, follow the market Move forward. ?
2. Communicate more with users. As real users, they can often provide manufacturers with more useful suggestions, such as the latest production needs, suggestions for the improvement of small-sized waste paper baler equipment, etc., only the suggestions of most users are integrated. In order to better produce high-quality products, so as to create favorable conditions for sales.for more information ,please visit :www.nickbaler.net
1. The equipment should be operated by human beings, and others are not allowed to use it arbitrarily without training.
2. Before driving, check whether all parts are normal and whether the fasteners are firm.
3. It is prohibited to cut unannealed steel parts, cast iron parts, soft metal parts, over-thin parts, parts less than 100 mm in length, and parts that exceed the length of the scissors.
4. During operation, the human body is forbidden to be close to the transmission part and the knife edge of the equipment, and the safety of the surrounding personnel should be paid attention to to prevent the material from lifting up and hurting people. When cutting, the material should be cut as close as possible to the inside of the knife. When cutting shorter materials, do not use hand-held workpieces to feed materials, and use clamps to feed materials.
5. When the equipment is running, the operator is not allowed to leave the post privately, and the power supply should be blocked when the operation is over or temporarily leaving the post.
Nick machinery does not need to install anchor screws, in places where there is no power supply can use diesel engines as power. For more information, contact 86-29-86031588
This series of equipment is classified into two types: vertical type and horizontal type.
Components:
This series of equipment is mainly composed of the following components:
①Main machine: It is composed of frame, main hydraulic cylinder, pusher hydraulic cylinder, bottom hydraulic cylinder, matching mold frame and mold, and indenter number.
The frame part is composed of upper and lower beams and uprights. The upper and lower beams are all made of all cast steel parts. The upper and lower beams are connected by inner and outer nuts with four columns to withstand the tension during operation.
The main hydraulic cylinder eliminates steel castings and eliminates safety hazards. Ensure the service life and operational safety of the equipment. Supporting mold frames and molds, the top number of indenters, through professional planning, cooperation, and superior processing capabilities are the guarantee for an outstanding taste of the equipment.
②Hydraulic station: It is composed of motor, hydraulic pump, pump protection device, professional control valve block and piping system for connecting briquetting machine. The planning is reasonable and the quality is stable. Equipped with a cooling system to prevent the equipment from being unable to operate continuously due to overheating of the oil.
③Console: It is composed of electrical system and plc control system.
Equipped with an adjustable text display, the sequence of actions and each action moment are completely controlled by the PLC system, and can be adjusted by the operator at any time, which is convenient and quick, simple and easy to understand.
Nick Machinery's metal baler is mainly suitable for steel mills, recycling and processing industries and non-ferrous and ferrous metal smelting industries. Contact consultation telephone 86-29-86031588
The mechanical processing method is to use special scrap steel processing machinery to process the scrap steel, to achieve the purpose of improving the quality of the scrap steel, which is conducive to the tempering of the furnace and the convenience of transportation.
There are many types of scrap steel processing machinery, and users can choose appropriate scrap steel processing equipment according to the processing requirements of scrap steel and the scale of production and economic capacity of the enterprise.
At that time, scrap steel processing equipment was divided into processing and auxiliary feeding equipment. Processing methods include Baler, briquetting, cutting, crushing, etc.
1. Mechanical packaging method
The mechanical baling method is to use a metal baler at room temperature to limit the frivolous steel scrap into bales with a certain shape and density. This kind of bale can be exercised in the furnace, and it is also easy to transport, which saves transportation capacity and reduces environmental pollution during transportation. The equipment used is a metal baler.
2. Mechanical briquetting method
Many metal cutting processes in the production process of the machinery industry produce a lot of steel chips, cast iron chips, copper chips, aluminum chips and other chips. If these chips are discarded, it will not only waste resources, but also severely pollute the environment. Taking it back and returning it to the oven after processing is a useful way to deal with it.
The processing equipment for metal chips is a metal chip briquetting machine, whose processing method is to directly limit cast iron chips, copper chips, and aluminum chips into a cylinder with a higher density at room temperature. If it is a long strip of steel shavings, the steel shavings should be broken before the restriction, and then restricted.
The scrap steel briquettes processed by the briquetting machine generally have a density of more than 4500kg/m3, which greatly reduces the volume of the scraps, improves the transportation capacity and can be returned to the furnace for exercise, and can also reduce the environmental pollution during transportation. The equipment used is: Metal briquetting machine.
3. Mechanical shearing method
The so-called shearing is to use a scrap shearing machine to cut the long strip of steel scrap to a suitable length for training. Nowadays, the scrap steel shearing machine has three types of structure: crocodile type, double-edged crocodile type and portal type. The equipment used is: metal shearing Machine, box-type shearing machine, heavy-duty shearing machine, etc.
Nick Machinery's automatic hydraulic baler is an unmanned operation of fully automatic compression and Baler, suitable for places with a lot of materials, reducing labor expenditures and improving work efficiency. https://www.nickbaler.net
