The use of any equipment has its own characteristics, and the cardboard balers are no exception. Compared with the semi-active cardboard balers, the cardboard balers are not from the structure of the equipment or the degree of maintenance and repair. It is much messier than semi-active cardboard baler, so it is slightly different from semi-active cardboard baler in application.
1.The Baler Press tape should be returned to the reel after the work is completed every day. Cardboard Baler Press machine use: Cardboard Baler Press machine can be used for various non-metallic compression Baler Press. Such as: cardboard, carton, shredded paper, cotton yarn, wool ball, plastic, grass and wood, sponge, wool, loose fiber, clothing, cloth, tobacco, plastic and other light foam and loose materials. The Baler Press belt of the cardboard Baler Press machine is not directly transported from the Baler Press reel to the core position, but from the storage box of the cardboard Baler Press machine to the movement. The Baler Press belt in the storage box is in a "Z" shape Stored, so it will be bent if it is not taken out for a long time, so that the tape will not be in place or jammed when it is used again the next day.
2. Prevent strong light from shining. Cardboard Baler Press machine use: Cardboard Baler Press machine can be used for various non-metallic compression Baler Press. Such as: cardboard, carton, shredded paper, cotton yarn, wool ball, plastic, grass and wood, sponge, wool, loose fiber, clothing, cloth, tobacco, plastic and other light foam and loose materials. This requirement is unique to the cardboard Baler Press machine, because the detection (check and test) equipment of the cardboard Baler Press machine is a photoelectric sensor, and the photoelectric sensor will fail when it encounters strong light. This is a semi-active hard Neither the cardboard packer nor the active cardboard packer has it.
3. If the cardboard Baler Press machine is used for a long time, its heating sheet will be very hot, so please do not touch the heating sheet of the cardboard Baler Press machine directly with your hands to avoid unnecessary damage to people. The cardboard baler is mainly suitable for steel mills, recovery processing occupations and non-ferrous and ferrous metal training occupations. The cardboard baler can knead all kinds of metal scraps (steel shavings, scrap steel, scrap aluminum, scrap copper, scrap stainless steel, scrap car scraps, etc.) into qualified furnace materials of various shapes such as cuboid, octagon, cylinder, etc. Reduce the cost of transportation and exercise, but also increase the furnace casting speed. During the operation of the equipment, you cannot cross the track with your head and hands. This behavior is a proper risk. We must keep in mind that the safety list is top
Nick Baler Hydraulic Baler Press Factory will never stop, will continue to improve the quality and function of the product itself, and produce better quality mechanical equipment for a wide range of users. Thank you for your support! for more information ,please visit :www.nickbaler.net
Common failure phenomenon: the entire hydraulic system of the waste paper baler has no pressure or insufficient pressure.
Common causes of failure: the overflow valve fails, and the oil pump is not working properly.
Solution: Check the type of overflow valve used in the waste paper baler equipment. If it is a pilot-operated overflow valve, there are many causes.
1. The overflow valve is stuck or the solenoid fails. If the overflow valve is stuck, clean the overflow valve and reinstall it. If it is electromagnetic failure, you need to check whether the circuit is open, and check whether the coil of the overflow valve is burned. If there is a problem with the circuit, repair the circuit; if the coil burns out, the coil needs to be replaced.
2. If it is the internal wear of the overflow valve, the overflow valve needs to be replaced at this time.
Waste paper baler is an environmental protection equipment that uses hydraulic principles to compress waste paper and waste cardboard into blocks, which is beneficial to waste paper storage, transportation and utilization. https://www.nickbaler.net
The oil pump of the horizontal waste paper baler generally has a plunger pump and a vane pump. The reasons for the loud noise of the oil pump system may include: loosening of the fastening screws of the oil pump; wear of the power bearing or stator of the oil pump; serious damage to the oil pump; inside the oil tank Air bubbles, poor oil intake of the hydraulic pump and other reasons will cause this problem. At this time, we should analyze the specific situation and solve the problem of excessive noise in the hydraulic waste paper baler oil pump!
The possible causes of the failure of the oil pump overheating problem are that the oil pipe is blocked, causing the pressure of the hydraulic oil to increase; the power of the oil pump is too large and overloaded; the hydraulic oil is used unreasonably and the viscosity is too high.
The quality of the hydraulic oil of the hydraulic waste paper Baler has a great influence on the hydraulic pump. The replacement cycle of the plunger pump is generally one year. If the plunger pump is noisy, it is recommended to consider replacing the plunger pump plunger.
The waste paper baler is used to extrude waste paper and similar products under normal conditions to greatly reduce the volume, so as to reduce the transportation volume, save the freight, and increase the benefits for the enterprise. https://www.nickbaler.net
The method of refueling the newly purchased waste paper baler equipment before starting, and the oil leakage problem of the newly purchased horizontal waste paper baler equipment has been plagued by the majority of user groups, so how to solve the problem of the waste paper baler oil Well, let's take a look at the waste paper baler equipment with Nick Machinery. What should I pay attention to when using the refueling method?
1. The oil leakage of the waste paper baler is relatively severe. If the oil pump pressure is adjusted too high, the wear of the movable parts will increase the sealing gap, the sealing device will be damaged, the viscosity of the oil used in the waste paper baler will be too low, etc., which will increase the leakage. After clarifying the reason, adopt the corresponding steps to eliminate it.
2. Poor heat dissipation, insufficient heat dissipation area of ??the fuel tank, too little oil storage in the fuel tank, resulting in too fast oil circulation, poor cooling of the waste paper Baler cooler, such as failure of cooling water supply or failure of electric fans, high ambient temperature, etc. All are the reasons for poor heat dissipation.
3. The system does not have an unloading circuit or the unloading circuit does not perform well. When the waste paper baler system does not need to pressurize the oil, the oil is still overflowing to the fuel tank under the working pressure set by the overflow valve or at the unloading pressure Return to the fuel tank downstream in a higher environment.
4. Misuse of oil with too high viscosity, the waste paper baler will cause excessive hydraulic loss.
The horizontal waste paper baler can be customized in different models according to the different needs of customers.https://www.nickbaler.net
