The waste paper baler can press waste paper,waste plastic bottles,various waste plastic films,etc,and bundle them,but automatically pack them into bags.However,when we use the waste paper baler,we will encounter the heat of the hydraulic oil of the waste paper baler.So what is the cause of the heat of the hydraulic oil of the waste paper baler?
1.Whether the friction of hydraulic components is within the specified range,the purity of the hydraulic oil,whether the hydraulic valve is over-pressured,etc.
2.Whether the oil supply of the oil pump is accurate,whether the selection of hydraulic components is reasonable,and there must be no uneven specifications or overflow of the overflow valve and heat.
3.The matching clearance is too small,or the clearance is too large after use and wear,and the internal and external leakage is large, resulting in large volume loss, such as the reduction of the volumetric efficiency of the pump and the rapid heating.
4.The volume of the fuel tank is too small,the heat dissipation area is not enough,the oil cooling device is not installed,or although there is a cooling device,its capacity is too small.
5.Whether the viscosity of the hydraulic oil is too large,whether the quality and standards are in accordance with the requirements,refuse to buy inferior hydraulic oil
6. Whether the hydraulic system is too tightly sealed,it should not be adjusted at will,the tightness should be ensured,and the operation should be performed in accordance with the standard.
The above are the reasons for the heating of the hydraulic oil of the waste paper baler. Nick brand waste paper baler is safe,reliable,low power consumption,economical and reasonable,easy to use,simple to maintain and operate.It is a good helper for your production.
The automatic waste paper baler needs to be turned on and checked before it is used. It can be put into use after the startup and check everything is normal. The check contents are as follows:
1. The location, temperature and cleanliness of hydraulic oil. Hydraulic oil is generally not a problem, so it only needs to be checked regularly.
2. It is summer now, and the rain is relatively abundant. If the baler is placed outdoors, be sure to do a good job of coping with it before and after the rain. Such as: whether the circuit is smooth, whether there is water in the box
3. Check whether the conveying of the conveyor is normal
4. Look around the machine, comprehensively check whether the equipment is normal, and ensure that the work is correct before feeding.
If the operator develops the good habit of daily inspection, it can not only maintain the normal production of the equipment, but also bring greater value to the production.
NICKBALER Machinery warmly reminds you: When using the baler, you should strictly follow the operating instructions. For more information on maintenance, please follow us https://www.nickbaler.net
The hydraulic baler mainly uses the hydraulic cylinder to "output" objects, but once the hydraulic cylinder has a problem, it will not only affect the normal use, but also need to determine the fault. Today, some customers responded that the hydraulic baler oil cylinder could not go up and down, as if it was stuck. What is the cause? How can we trouble shoot the problem?
First check the hydraulic baler oil cylinder and eliminate it step by step as follows:
1.First find a pressure gauge to check the pressure in the valve? And know the stroke and working pressure of the hydraulic cylinder.
2.Check each fitting on the hydraulic valve block for oil seepage or leakage. And know if the manual generation or the control generation is working properly.
3.Whether the load when the hydraulic cylinder is loaded is abnormal.
4.To remove the above is to see if the working pressure of the overflow raft is low, and then adjust it.
5.If none of the above is to consider whether the cylinder is stuck or there is an obstruction in the valve block.
NICKBALER machinery provides: horizontal hydraulic baler, vertical hydraulic baler, waste paper baler and other baling machine equipment, company website: www.nkbaler.net, telephone: 86-29-86031588, looking forward to long-term cooperation with you!
How to choose the type to process 10 tons of waste paper every day?
First of all, NICKBALER suggests that if the daily processing capacity reaches 10 tons, you can choose a horizontal baler, and the horizontal baler is divided into: semi-automatic baler and full-automatic baler; if the initial investment is limited, you can use the semi-automatic baler. Choose from the baler, and the smallest model NKW60BD can meet the production requirements;
If you have a spacious site and sufficient funds, and have better development and planning in the future,NICKBALER suggests that you can choose a fully automatic baler; what is the difference between a semi-automatic baler and a fully automatic baler?
1. The architecture is different
2. Different packing methods
3. The output is different
Waste paper baler is our main product for many years, we have very valuable experience, if you want to know more, please follow us https://www.nickbaler.net