With the improvement of people’s awareness of environmental protection,the waste paper produced in our daily lives is recycled and reused by waste paper balers. Waste paper balers are increasingly accepted by everyone,but when we use waste paper balers,In order to avoid accidents,the safe operating procedures of the waste paper hydraulic baler must be known!
1.Before starting the machine,check whether the compressed air pressure meets the requirements,check whether the main components are in good condition,such as heating belts,scissors and other parts of the cart,and check whether there are other people around the machine to ensure that the machine is safe to open.
2.Turn off the main power air switch,turn on the power to start,set and check the temperature of each temperature controller,roll the film intact, adjust the color mark,put a section of code ribbon, determine the code date and related characters and the products produced on the same day does it reach the requirement.
3.Turn on the CIP cleaning system and clean the feeding system and measuring machine before production to ensure product hygiene.
4.First adjust the bagging and check the coding effect.At the same time,open the feeding system to feed.When the material meets the requirements,first open the bag of the bagging mechanism,check the vacuum and heat sealing quality of the vacuum box,and vacuum the bag.After meeting the requirements,start filling materials and start production.
5.If there is a problem with the equipment or the product quality is unqualified during the production process,the machine should be shut down immediately to solve the problem.It is strictly forbidden to deal with problems during the operation of the machine to prevent accidents.
6.The operator of the waste paper baler is not allowed to adjust certain operating parameters of the machine,such as the number of operations,various parameters of the servo and inverter.If adjustment is needed,the relevant maintenance personnel or technicians should make adjustments together.
7.In the production process,check the quality of the product at any time,and adjust at any time if there is any problem.
8.Operators should pay attention to the safety of themselves and others at all times during operation.
The above are even some operating specifications for the operation of the waste paper baler,remind everyone that you must pay attention to safety when operating the waste paper baler.The Nick brand waste paper baler is simple to operate and automatically discharges the bale,which improves work efficiency.The installation of emergency stop settings makes the operation safer and the after-sales perfect.
Reed balers, timber balers, hydraulic balers
For the purpose of protecting the environment, the country has strict control measures on the deforestation of virgin forests, and now it is an era of high paper and cardboard output and consumption, which has caused a serious shortage of paper-making raw materials. Nowadays, wood is mainly used as the main raw material for papermaking. In the planning of the papermaking industry, it is clearly stated that in the future, the papermaking raw materials should form a wood fiber material, increase the recycling rate of waste paper, and encourage the diversification of non-wood raw materials. Raw material structure. From this point of view, as a form of non-wood fiber papermaking, reed pulping and papermaking has very important practical significance in our country.
By analyzing the status quo of the papermaking, animal husbandry and straw wood-based panel industries, it is concluded that the demand for these three industries will increase at a relatively high rate now and in the future, but at the same time they have to face the situation that the lack of raw materials affects production. Modern production and processing techniques have solved the feasibility of using reed as a raw material in these three industries. my country is rich in reed resources, but except for a small part of the reed resources that are used, most of them are in a primitive state of self-sustaining. The reason is that the general reed growing area is far away from the factory, and the transportation cost of loose reeds is high, which restricts enterprises. The use of reeds. It is under this background that a reed baler is proposed to solve the serious loss of tonnage caused by loose materials and low bulk density during transportation by packaging the reeds. The reed is packed by a baler to increase the bulk density of the reed, so as to achieve the purpose of reducing freight and increasing the utilization rate of the reed.
NKBALER is a professional manufacturer of waste paper baler, carton baler, straw baler, paper shell hydraulic baler, clothing hydraulic baler, rice husk hydraulic baler, plastic bottle hydraulic baler and other automatic balers and semi-automatic balers Manufacturer.
1. Shearing oil cylinder: It is a double-acting single-piston rod type oil cylinder. Its front end is connected with the frame, and the rear part is connected with the machine base by lower pins (one on each side), and the frame shaft is driven by the push-out and retraction of the piston rod. swing. Implement the cutting action.
2 Frames: The frame is an important flowing part. The left side of the front part is equipped with an upper shear. The middle is connected with the frame by the frame shaft and frame bushing, and the rear is connected with the upper pin shaft of the shear cylinder. .
3. Machine base: It is composed of welding base, left frame, right frame, etc. The right frame and the left frame of the base are welded parts, of which the right and left frames use inner and outer (double) side plates, and the structure is firm.
4. There is a platform and a slope at the front of the machine base, and a lower shear is installed between them. There is a large hole in the middle of the left and right frames for installing the frame, and there is a hole in the rear for installing the shearing cylinder. The front part of the frame is welded with a pressure material cylinder bracket, which is used to install the pressure material cylinder and other portal metal shears.
NICKBALER has rich production experience and integrated services. Using our balers can greatly improve work efficiency and reduce human and financial expenditures. Contact us at 86-29-86031588 or https://www.nkbaler.net/.
The semi-automatic plastic bottle Baling machine is mainly used for Baling machinewaste products, but because it is semi-automatic packing, it needs to be worn manually. Many friends do not know how to operate it. NKBALER has summarized the following points based on experience , I hope it can help everyone.
Semi-automatic plastic bottle Baling machine strapping method:
1. Install the pp tape on the pp tape mounting roller.
2. There is a brake pad connected to the "L"-shaped metal rod on the roller and the fuselage. There are two white rollers on the metal rod. middle.
3. After the upper and lower extensions are inserted, press the connecting spring on the front of the upper extension (the machine is turned on at this time).Line packing.
The above is the method of wearing the semi-automatic plastic bottle baler. I believe that through the introduction, everyone has a deeper understanding of how to operate the plastic baler. If you have other questions, you can leave a message for consultation.https://www.nkbaler.net/.