The metal shavings briquetting machine can directly cold press powdered cast iron shavings,steel shavings,copper shavings,aluminum shavings,excellent mineral powders,etc. into cakes for easy transportation and casting.Not only does it ensure that the original raw materials remain unchanged,the water output rate is increased,and the recovery loss of the furnace does not exceed 10%.The molding also ensures that the original raw materials remain unchanged.The metal chip briquetting machine flow control valve uses the saving port area between the regulating spool and the valve body and the part of the resistance it generates to regulate the flow,thereby controlling the movement speed of the fulfilling element.The flow control valve is divided into 5 types according to its use:
1.Saving valve:After setting the saving port area,the movement speed of the fulfillment element that does not change much in load pressure and does not require high uniformity of movement is basically stable.
2.Speed:control valve:When the load pressure changes,the pressure difference between the inlet and outlet of the saving valve can be maintained as a fixed value.In this way,after the saving port area is adjusted,no matter how the load pressure changes,the speed control valve can maintain the same flow rate through the saving valve,so that the movement speed of the fulfilling element is stable.
3.Diversion valve:Regardless of the size of the load,the equal diversion valve or synchronization valve can be used to obtain the same flow of two fulfillment elements of the same oil source;the share diversion valve is the share distribution valve that obtains the flow according to the share.
4.Collecting valve:The effect is opposite to that of the diverting valve,so that the flow into the collecting valve is distributed in proportion.
5.Diverting and collecting valve:It has both functions of dividing valve and collecting valve.
Nick brand metal baler is easy to operate, safe and energy-saving, it is your best helper.
1. Shearing oil cylinder: It is a double-acting single-piston rod type oil cylinder. Its front end is connected with the frame, and the rear part is connected with the machine base by lower pins (one on each side), and the frame shaft is driven by the push-out and retraction of the piston rod. swing. Implement the cutting action.
2 Frames: The frame is an important flowing part. The left side of the front part is equipped with an upper shear. The middle is connected with the frame by the frame shaft and frame bushing, and the rear is connected with the upper pin shaft of the shear cylinder. .
3. Machine base: It is composed of welding base, left frame, right frame, etc. The right frame and the left frame of the base are welded parts, of which the right and left frames use inner and outer (double) side plates, and the structure is firm.
4. There is a platform and a slope at the front of the machine base, and a lower shear is installed between them. There is a large hole in the middle of the left and right frames for installing the frame, and there is a hole in the rear for installing the shearing cylinder. The front part of the frame is welded with a pressure material cylinder bracket, which is used to install the pressure material cylinder and other portal metal shears.
NICKBALER has rich production experience and integrated services. Using our balers can greatly improve work efficiency and reduce human and financial expenditures. Contact us at 86-29-86031588 or https://www.nkbaler.net/.
The semi-automatic plastic bottle Baling machine is mainly used for Baling machinewaste products, but because it is semi-automatic packing, it needs to be worn manually. Many friends do not know how to operate it. NKBALER has summarized the following points based on experience , I hope it can help everyone.
Semi-automatic plastic bottle Baling machine strapping method:
1. Install the pp tape on the pp tape mounting roller.
2. There is a brake pad connected to the "L"-shaped metal rod on the roller and the fuselage. There are two white rollers on the metal rod. middle.
3. After the upper and lower extensions are inserted, press the connecting spring on the front of the upper extension (the machine is turned on at this time).Line packing.
The above is the method of wearing the semi-automatic plastic bottle baler. I believe that through the introduction, everyone has a deeper understanding of how to operate the plastic baler. If you have other questions, you can leave a message for consultation.https://www.nkbaler.net/.
The electrical control part of the waste paper baler is mainly composed of PLC, motor and electrical components of relays and switches. The most vulnerable parts of these parts are the motor and electrical components. Today we share with you: baler electrical control Box Daily Precautions
1. Pay attention to the grounding, lightning protection, rainproof and moisture-proof of the power cord.
2. Non-professional operators of the electric control cabinet are prohibited from using it.
3. Pay attention to the antifreeze work of the motor and the long-term overload of the motor. Effective prevention of these two items can greatly reduce the damage to the motor, thereby maintaining the normal Baling machineof the waste paper baler.
4. Pay attention to the button operation of the console part, do not use too much force on the switch button, and prevent misoperation to avoid damage caused by short circuit.
The above 4 points are what I want to share with you today, I hope it can help you!
NKBALER provides: horizontal hydraulic baler, vertical hydraulic baler, waste paper baler and other Baling machineequipment, company website: https://www.nkbaler.net/. Tel: 86-29-86031588, looking forward to contacting your cooperation!