With the increasing awareness of environmental protection,the household garbage compression Baling Machine has played a great effect,and its operating principle has become clearer.Nick's domestic waste Baling Machine keeps pace with the times,creating practical,centered,and hydraulic Baling Machine for domestic environmental protection.
Let's take a look at the operation process of the household waste Baling machine:
1.The hydraulic oil must be added to the specified oil level line before use.
2.Before starting the hydraulic pump check whether the circuit is incorrectly connected or leaked.
3.When Baling the household garbage Baling Machine,the operator must pay attention to safety,spread the paper evenly and in place,and close the lid of the box to start the Baling.
4.After Baling,all hydraulic rods must be retracted into the hydraulic cylinder to prevent dust from damaging the sealing ring and oil leakage.
5.The domestic garbage Baling Machines should be maintained regularly,and if oil leaks are found in the oil pipes,they should be dealt with by a mechanic immediately.
6.After the lid door is opened,pressing the door is strictly prohibited to prevent accidents.
7.Oil pressure:It is strictly forbidden to adjust the pressure privately.The operator must work under the adjusted oil pressure,and the high limit pressure is 30mpa.
8.The oil in the oil tank must be strictly filtered and always maintain a sufficient amount of oil.The oil tank should be cleaned and replaced every six months.
9.The lubrication points of the machine should be filled with lubricating oil at least once a day as required,and the debris in the cavity should be cleaned up every shift.
10.Those who do not understand the main machine structure,performance and operating procedures shall not operate the machine privately.When multiple people operate at the same time, he division of labor should be clear to prevent the risk of misoperation.
11.When the machine shows oil leakage or an abnormal phenomenon occurs during operation,the vehicle should be parked immediately.Don't look at the place where the oil is sprayed,don't just use your hands to block it,and don't run it with illness.
12.When the household garbage Baling Machine is in operation or Baling,it is not allowed to repair or touch the moving parts by hand,and it is strictly forbidden to press materials in the bin with hands or feet.
13.The adjustment of pumps,valves,and pressure gauges must be carried out by experienced technicians.If faults are found in the pressure gauges,they should be repaired or replaced immediately.
14.This machine uses 46# anti-wear oil,always pay attention to the oil temperature,and stop it when it exceeds 75°C.
15.When turning the package,pull the handle of the cover cylinder to the return position,and then push the turning handle.
Nick brand household waste Baling Machine has good rigidity,toughness and stability,beautiful appearance,convenient operation and maintenance,safe and energy-saving,and low investment in equipment basic engineering.It is a good helper for your life.
1. The equipment should be operated by human beings, and others are not allowed to use it arbitrarily without training.
2. Before driving, check whether all parts are normal and whether the fasteners are firm.
3. It is prohibited to cut unannealed steel parts, cast iron parts, soft metal parts, over-thin parts, parts less than 100 mm in length, and parts that exceed the length of the scissors.
4. During operation, the human body is forbidden to be close to the transmission part and the knife edge of the equipment, and the safety of the surrounding personnel should be paid attention to to prevent the material from lifting up and hurting people. When cutting, the material should be cut as close as possible to the inside of the knife. When cutting shorter materials, do not use hand-held workpieces to feed materials, and use clamps to feed materials.
5. When the equipment is running, the operator is not allowed to leave the post privately, and the power supply should be blocked when the operation is over or temporarily leaving the post.
This series of equipment is classified into two types: vertical type and horizontal type.
This series of equipment is mainly composed of the following components:
The frame part is composed of upper and lower beams and uprights. The upper and lower beams are all made of all cast steel parts. The upper and lower beams are connected by inner and outer nuts with four columns to withstand the tension during operation.
The main hydraulic cylinder eliminates steel castings and eliminates safety hazards. Ensure the service life and operational safety of the equipment. Supporting mold frames and molds, the top number of indenters, through professional planning, cooperation, and superior processing capabilities are the guarantee for an outstanding taste of the equipment.
②Hydraulic station: It is composed of motor, hydraulic pump, pump protection device, professional control valve block and piping system for connecting briquetting machine. The planning is reasonable and the quality is stable. Equipped with a cooling system to prevent the equipment from being unable to operate continuously due to overheating of the oil.
③Console: It is composed of electrical system and plc control system.
Equipped with an adjustable text display, the sequence of actions and each action moment are completely controlled by the PLC system, and can be adjusted by the operator at any time, which is convenient and quick, simple and easy to understand.
Nick Machinery's metal baler is mainly suitable for steel mills, recycling and processing industries and non-ferrous and ferrous metal smelting industries. Contact consultation telephone 86-29-86031588
The mechanical processing method is to use special scrap steel processing machinery to process the scrap steel, to achieve the purpose of improving the quality of the scrap steel, which is conducive to the tempering of the furnace and the convenience of transportation.
There are many types of scrap steel processing machinery, and users can choose appropriate scrap steel processing equipment according to the processing requirements of scrap steel and the scale of production and economic capacity of the enterprise.
At that time, scrap steel processing equipment was divided into processing and auxiliary feeding equipment. Processing methods include Baler, briquetting, cutting, crushing, etc.
1. Mechanical packaging method
The mechanical baling method is to use a metal baler at room temperature to limit the frivolous steel scrap into bales with a certain shape and density. This kind of bale can be exercised in the furnace, and it is also easy to transport, which saves transportation capacity and reduces environmental pollution during transportation. The equipment used is a metal baler.
Many metal cutting processes in the production process of the machinery industry produce a lot of steel chips, cast iron chips, copper chips, aluminum chips and other chips. If these chips are discarded, it will not only waste resources, but also severely pollute the environment. Taking it back and returning it to the oven after processing is a useful way to deal with it.
The processing equipment for metal chips is a metal chip briquetting machine, whose processing method is to directly limit cast iron chips, copper chips, and aluminum chips into a cylinder with a higher density at room temperature. If it is a long strip of steel shavings, the steel shavings should be broken before the restriction, and then restricted.
The scrap steel briquettes processed by the briquetting machine generally have a density of more than 4500kg/m3, which greatly reduces the volume of the scraps, improves the transportation capacity and can be returned to the furnace for exercise, and can also reduce the environmental pollution during transportation. The equipment used is: Metal briquetting machine.
3. Mechanical shearing method
The so-called shearing is to use a scrap shearing machine to cut the long strip of steel scrap to a suitable length for training. Nowadays, the scrap steel shearing machine has three types of structure: crocodile type, double-edged crocodile type and portal type. The equipment used is: metal shearing Machine, box-type shearing machine, heavy-duty shearing machine, etc.
Nick Machinery's automatic hydraulic baler is an unmanned operation of fully automatic compression and Baler, suitable for places with a lot of materials, reducing labor expenditures and improving work efficiency. https://www.nickbaler.net