With the progress of society,people's living standards are constantly improving,but more and more domestic garbage is also coming.All kinds of used TVs,washing machines,refrigerators,etc.need to be recycled,but these things are all metals,which makes it difficult to handle.But the metal chip shredder makes everything easier.
Because the metal chip shredder is the particularity of shredding materials,in order to prevent excessive loss of equipment blades,we need to maintain and maintain it frequently.
First of all,the maintenance of one of the important parts of the metal chip pulverizer requires us to observe whether the lubricant of the bearing is replaced in time.Generally,it is required to add new lubricant after 320 hours of production.
Second,at the beginning,let the equipment run in idling for a while,then slowly add materials,and then normal discharge after a few minutes.
When discharging,the materials should be put in stably,which can effectively save time and increase work efficiency.
Nick brand metal chip shredder is recognized by many customers with high-quality qualifications and professional craftsmanship according to everyone's actual needs,and is worthy of trust.
In daily life,no matter how good the equipment is,if there is no good sense of inspection and maintenance, t will affect the efficiency of the machine over time.
Everyone knows that the nature of the metal,the shearing temperature and other factors will affect the shearing quality of the shearing machine.To a large extent,the lack of maintenance and maintenance awareness will cause some unnecessary troubles.
We have classified the failures of the shearing machine in daily use:the oil cylinder,the oil pump,and the cutting blade.
1.In terms of oil cylinder:After the machine is powered on,the oil cylinder cannot generate pressure.At this time,it is because the oil contains impurities in the process of sucking oil for a long time,which causes the overflow valve to block.
2.Oil pump:After the machine is started,if the oil pump does not work,check the electromagnet or replace the electromagnet.It is very likely that the electromagnet loop fails due to long-term use and cannot generate magnetic force;
Or the spool is stuck due to dust entering the steering valve spool,causing the oil pump to fail to work.
3.In terms of cutting edge:Too high or too low cutting edge will result in non-standard distance between the blade gap.During the cutting process,the cut material will be irregular and the quality is poor.
The above 3 points are that you have encountered more in the process of use.Others include failures such as insufficient oil and air supply due to the rupture of the oil suction pipe.
These are things that everyone should always pay attention to during use.Only by mastering these common faults,we will be more comfortable when using the shearing machine.
According to the actual needs of everyone,the Nick brand shearing machine has been recognized by many customers with high-quality qualifications and professional craftsmanship and is trustworthy.
What are the hazards caused by the contaminants produced by the hydraulic system of the metal briquetting press to our machinery and equipment?In fact,70% of the failures of this product are caused by the oil inside,so daily cleaning is very necessary.
There are two ways of pollution of the metal briquetting machine,one is the potential pollution of the system during production and installation,and the other is the pollution caused by improper cleaning during operation.
If the material is not cleaned in time,it will block the orifice gap of the metal briquetting machine,thereby changing the working performance of the machine.Moreover,the pollutants will also accelerate the wear of the parts of the metal briquetting machine.The common one is burning,and then the valve is caused.Failure to produce noise.
So everyone should pay attention to the maintenance of the metal briquetting machine,check on time and repair it in time,so as to better produce.
Nick brand metal briquetting machine has good rigidity,toughness and volatility,beautiful appearance,convenient operation and maintenance,safe and energy-saving,it is a good helper for your production.
Company website:www.nkbaler.com,or call:86-29-86031588
When starting a business,what is the biggest cost besides labor?The human cost in society is the highest now,but there is another one that cannot be ignored,and that is the plant land,which is also more expensive.
Some data show that there are several kinds of metal scraps that have relatively high densities,especially aluminum scraps and copper scraps,which are not only large in quantity but also particularly fluffy,occupying a lot of space. This kind of waste is not easy to sort out and easy to throw away.It requires a lot of bags or empty space to store these waste materials,and it also wastes labor.
The metal baler can make the volume of these waste materials smaller,increase the density,and can be squeezed into blocks for convenient storage and save labor.The NKY81-1600B metal baler produced by Nick Machinery has simple structure,stable action,simple operation,low failure rate and easy cleaning and maintenance.It is a good helper for your production