Today’s market is uncertain,changing circumstances,and strict environmental protection inspections have caused steel plants to have strict requirements on smelting scrap iron and steel raw materials,especially for the extremely high control of the impurity rate of the scrap iron lumps,requiring the size of the scrap iron lumps not to exceed 400*400 Mm,the impurity in the bale should be low,otherwise severe punishment and deduction.
Such strict requirements are facing severe tests for the scrap iron recycling industry.The size of the bales packed in the scrap iron recycling industry should be controlled within 400*400 mm in the process of recycling scrap iron,which is convenient for furnace entry and saves energy in the smelting process. ,Emissions are more environmentally friendly.
The NKY81-2000A metal bailer press produced by Nickel can perfectly meet your needs and produce bales that meet the requirements of recycling.
The oil pump of the horizontal waste paper baler generally has a plunger pump and a vane pump. The reasons for the loud noise of the oil pump system may include: loosening of the fastening screws of the oil pump; wear of the power bearing or stator of the oil pump; serious damage to the oil pump; inside the oil tank Air bubbles, poor oil intake of the hydraulic pump and other reasons will cause this problem. At this time, we should analyze the specific situation and solve the problem of excessive noise in the hydraulic waste paper baler oil pump!
The possible causes of the failure of the oil pump overheating problem are that the oil pipe is blocked, causing the pressure of the hydraulic oil to increase; the power of the oil pump is too large and overloaded; the hydraulic oil is used unreasonably and the viscosity is too high.
The quality of the hydraulic oil of the hydraulic waste paper Baler has a great influence on the hydraulic pump. The replacement cycle of the plunger pump is generally one year. If the plunger pump is noisy, it is recommended to consider replacing the plunger pump plunger.
The waste paper baler is used to extrude waste paper and similar products under normal conditions to greatly reduce the volume, so as to reduce the transportation volume, save the freight, and increase the benefits for the enterprise. https://www.nickbaler.net
The method of refueling the newly purchased waste paper baler equipment before starting, and the oil leakage problem of the newly purchased horizontal waste paper baler equipment has been plagued by the majority of user groups, so how to solve the problem of the waste paper baler oil Well, let's take a look at the waste paper baler equipment with Nick Machinery. What should I pay attention to when using the refueling method?
1. The oil leakage of the waste paper baler is relatively severe. If the oil pump pressure is adjusted too high, the wear of the movable parts will increase the sealing gap, the sealing device will be damaged, the viscosity of the oil used in the waste paper baler will be too low, etc., which will increase the leakage. After clarifying the reason, adopt the corresponding steps to eliminate it.
2. Poor heat dissipation, insufficient heat dissipation area of ??the fuel tank, too little oil storage in the fuel tank, resulting in too fast oil circulation, poor cooling of the waste paper Baler cooler, such as failure of cooling water supply or failure of electric fans, high ambient temperature, etc. All are the reasons for poor heat dissipation.
3. The system does not have an unloading circuit or the unloading circuit does not perform well. When the waste paper baler system does not need to pressurize the oil, the oil is still overflowing to the fuel tank under the working pressure set by the overflow valve or at the unloading pressure Return to the fuel tank downstream in a higher environment.
4. Misuse of oil with too high viscosity, the waste paper baler will cause excessive hydraulic loss.
1. Automatic control mode, install the interlock switch
2. Independently install emergency stop button, which can stop emergency at any time in any state to ensure safety;
3. The pressure plate adopts the guide groove type balance to effectively prevent the tilt;
4. Hook type automatic package turning, easy to install;
5. Quickly lock and loosen the device, install it well and quickly.
Nick Machinery has rich production experience and integrated service. Using our baler can greatly improve work efficiency and reduce human and financial expenditure. Contact us at 86-29-86031588 or https://www.nickbaler.net