The cleaning operation of the hydraulic system in the waste baling machine is very effective for thebaling machine,because the waste baling machine requires a good hydraulic transmission equipment.Therefore,in the work task,the cleaning operation of the packer cannot be ignored and must be taken seriously.
First,use low-viscosity special cleaning oil,add the oil to the oil tank of the waste baling machine during cleaning and heat it to 50-80 degrees Celsius.Activate the hydraulic oil pump and let it run dry.When cleaning,you must tap the pipes lightly.The meaning of this type of operation is to remove the appendages. After cleaning for 20 minutes,check the environmental pollution status of the oil filter,and clean the filter,and then carry out the cleaning.It stops until there are not many pollutants on the filter.
It usually takes two hours to clean the waste baling machine.For the more disorderly hydraulic system,each area can be cleaned according to the working place.You can also plug in a hydraulic cylinder to allow the hydraulic cylinder to move multiple times to clean the equipment.
After cleaning,be sure to drain the cleaning oil as much as possible,and clean the inside of the engine oil tank. After that,the temporary cleaning circuit is disassembled,the waste baling machine repair system is in all normal use conditions,and hydraulic oil is added.
The Nick brand waste baling machine is easy to operate,high in safety,automatic out of the package,and more efficient.It is your best choice.
Company website:www.nickbaler.net, or call: 86-29-86031588
With the increasing frequency of the use of clothing balers, Nick Machinery has summarized some problems that should be paid attention to when using clothing balers. Although it seems to be a trivial matter, it has a great impact on the service life of the clothing balers. Sometimes It may also endanger the personal safety of the staff, so it should not be ignored! Now I will share with you a few common problems, I hope to help you:
1. Please confirm the power supply used by the machine and do not plug in the wrong power supply.
2. Remember to unplug the power supply when the machine is not in use.
3. The main parts should be lubricated with oil frequently.
4. Do not wash the machine with water. When the workplace is wet, the operator should not work barefoot.
5. Do not change the parts on the garment Baler machine at will.
6. Do not put your head or hands into the running machine.
Nick Machinery Garment Baler is specially used for the recycling and Baler of second-hand clothes, quilts, shoes and other products, and is widely used in old clothes recycling factories. www.nickbaler.net
Nowadays, the waste paper baler has become a good helper for people and brought great convenience to people. But sometimes there will be some glitches, such as unstable production. What is going on?
1. The production of waste paper baler is inseparable from the performance of the oil cylinder. The performance of the oil cylinder determines the stability of the waste paper baler. To ensure the production performance of the product, you must choose a manufacturer with exquisite craftsmanship of the cylinder.
2. The quality of the hydraulic oil selected by the waste paper baler, the quality of the hydraulic oil directly determines whether the cylinder can exert a large effect, and also directly affects the failure rate and service life of the cylinder. To ensure the production of waste paper baler, high-quality and genuine anti-wear hydraulic oil must be used.
3. The direct factors affecting the production efficiency of the waste paper baler: the model and specifications of the baler, the output varies from model to model, and the difference in specifications directly determines the production efficiency of the baler. The production efficiency of the conventional waste paper baler is higher than that of the equipment with a door at the discharge port.
4. The operation convenience, control performance and low failure rate of the waste paper baler control system also determine the baling operation efficiency.
Nick Machinery waste paper baler has good rigidity, toughness and stability, beautiful appearance, convenient operation and maintenance, safe and energy-saving, and low investment cost. www.nickbaler.net
The waste paper baler is an important part of waste paper recycling and is of great significance to the utilization of waste paper and other renewable resources. At the same time, the recovery rate of waste paper in my country is relatively low and needs to be further improved. This also shows that the application of waste paper baler is very necessary and needs further promotion and research.
In the mid-1970s, hydraulic baling presses began to be mass-produced and put into use. In the 1980s, large-tonnage hydraulic balers were also put into production. China's waste paper processing technology has made a new leap, and the quality of waste paper packaging has been improved.
Practice has proved that the hydraulic baler has compact structure, flexible operation, high degree of automation, long service life, large pressure tonnage, high waste paper density, saving packaging materials, reducing vehicle transportation losses, and considerable economic benefits.
With the continuous expansion of the recycling business of waste materials recycling stations, the utilization rate of waste paper balers in equipment maintenance plants is close to saturation, which cannot meet the storage requirements of recycling equipment. Therefore, the waste paper baler produced by our factory is simple to operate, flexible in action mechanism, and ingenious in design. It has the advantages of being simple, practical, fast and convenient. In addition, the European and American standard bullet-proof door structure can protect the safety of the operator; the automatic balancing device is equipped to avoid accidents caused by improper materials.