With the increase in agricultural output in my country,the amount of straw has also doubled.Among them,corn stalks are planted in a wide area,short production cycle,large yield,rich in nutrients and high-value polymer plant fibers,but this resource does not Get fully utilized.The main factors restricting the development of straw forage industry are:
1.Compared with grass stalks,in the production of food crops,due to the requirements of lodging resistance,stalks have higher silicon content and hard cortex,which is hard forage.It is straw forage to increase the forage rate and absorption rate of straw.The problem of grass utilization must be solved first.
2.The crude protein content of straw is low,especially yellow straw,life active substances vitamins,etc.have been destroyed,more than 80% of the soluble compounds are decomposed,the main component of crop straw is cellulose,which is responsible for the nutritional value of straw forage One of the reasons for the low.
However,as the basic feed for ruminants,straw is an indispensable filling for the stomach.Increasing the protein content of straw forage is a task that must be solved first in the utilization of straw forage.
But now there is a straw baler that can solve these problems.
The straw baler can press silage straw,dried corn stalks,various straw scraps,etc.,for bundling,and automatic bagging and packaging.
The Nick brand straw baler has simple structure,simple daily operation and maintenance,convenient transportation and storage,continuous operation and high efficiency.
1. Shearing oil cylinder: It is a double-acting single-piston rod type oil cylinder. Its front end is connected with the frame, and the rear part is connected with the machine base by lower pins (one on each side), and the frame shaft is driven by the push-out and retraction of the piston rod. swing. Implement the cutting action.
2 Frames: The frame is an important flowing part. The left side of the front part is equipped with an upper shear. The middle is connected with the frame by the frame shaft and frame bushing, and the rear is connected with the upper pin shaft of the shear cylinder. .
3. Machine base: It is composed of welding base, left frame, right frame, etc. The right frame and the left frame of the base are welded parts, of which the right and left frames use inner and outer (double) side plates, and the structure is firm.
4. There is a platform and a slope at the front of the machine base, and a lower shear is installed between them. There is a large hole in the middle of the left and right frames for installing the frame, and there is a hole in the rear for installing the shearing cylinder. The front part of the frame is welded with a pressure material cylinder bracket, which is used to install the pressure material cylinder and other portal metal shears.
NICKBALER has rich production experience and integrated services. Using our balers can greatly improve work efficiency and reduce human and financial expenditures. Contact us at 86-29-86031588 or https://www.nkbaler.net/.
The semi-automatic plastic bottle Baling machine is mainly used for Baling machinewaste products, but because it is semi-automatic packing, it needs to be worn manually. Many friends do not know how to operate it. NKBALER has summarized the following points based on experience , I hope it can help everyone.
Semi-automatic plastic bottle Baling machine strapping method:
1. Install the pp tape on the pp tape mounting roller.
2. There is a brake pad connected to the "L"-shaped metal rod on the roller and the fuselage. There are two white rollers on the metal rod. middle.
3. After the upper and lower extensions are inserted, press the connecting spring on the front of the upper extension (the machine is turned on at this time).Line packing.
The above is the method of wearing the semi-automatic plastic bottle baler. I believe that through the introduction, everyone has a deeper understanding of how to operate the plastic baler. If you have other questions, you can leave a message for consultation.https://www.nkbaler.net/.
The electrical control part of the waste paper baler is mainly composed of PLC, motor and electrical components of relays and switches. The most vulnerable parts of these parts are the motor and electrical components. Today we share with you: baler electrical control Box Daily Precautions
1. Pay attention to the grounding, lightning protection, rainproof and moisture-proof of the power cord.
2. Non-professional operators of the electric control cabinet are prohibited from using it.
3. Pay attention to the antifreeze work of the motor and the long-term overload of the motor. Effective prevention of these two items can greatly reduce the damage to the motor, thereby maintaining the normal Baling machineof the waste paper baler.
4. Pay attention to the button operation of the console part, do not use too much force on the switch button, and prevent misoperation to avoid damage caused by short circuit.
The above 4 points are what I want to share with you today, I hope it can help you!
NKBALER provides: horizontal hydraulic baler, vertical hydraulic baler, waste paper baler and other Baling machineequipment, company website: https://www.nkbaler.net/. Tel: 86-29-86031588, looking forward to contacting your cooperation!