The failures of straw baler oil pump not draining oil mainly include oil pump failure,oil suction pipe failure,fuel tank filter failure,and oil pump motor failure.If the straw baler oil pump fails to drain oil,check and eliminate the faults in turn according to the following methods
1.Stop immediately if the direction of rotation is wrong,and correct the direction of rotation of the motor.If it continues to burn or damage the oil pump.
2.The oil pump of the straw baler does not rotate.Repair the coupling.
3.The pump shaft is broken and the rotor does not rotate.Repair the oil pump.
4.The suction pipe is blocked,check the suction pipe.
5.The fuel tank filter is blocked,clean the filter or replace it.
6.The capacity of the fuel tank filter is insufficient.Replace with a larger capacity,which is more than 2 times the pump capacity.
7.The anti-wear hydraulic oil viscosity of the straw baler is too high.Change the oil type and install a heater.
8.The motor speed of the straw baler is insufficient.Replace the motor with the specified speed of the oil pump.
9.The suction pipe of the oil pump is not well sealed,and gas is present.Check the suction pipe.
10.The fuel tank filter should refuel at the top of the oil level or redesign the oil level.
11.The oil pump leaf cannot slide out of the rotor groove,repair the oil pump or replace the oil pump.
When the straw baler fails,check and eliminate it according to the above methods.If you cannot solve it by yourself,please be sure to find the manufacturer's after-sales personnel to come and repair it.
Nick Machinery provides you with a full range of services,whether it is pre-sales or after-sales,we have dedicated personnel to connect you to ensure your rights.
For more information about hydraulic baler,contact 86-029-86031588 or visit: www.nickbaler.net
Now that the application of plastic bottle balers has become more and more extensive, what preparations should we make when applying this product?
Next, let's follow the editor to find out.
The plastic bottle baler works for a long time and reaches a certain service life. In order to make the equipment play the overall value, the old parts need to be replaced. There are several aspects that need attention in the process of replacing the cylinder of the plastic bottle baler.
According to the correct disassembly method, on the one hand, the disassembly process is smooth and not damage the equipment; on the other hand, it is also to take care of safety issues.
Before disassembling the hydraulic cylinder of the mineral water bottle Baler, drain the hydraulic oil in the two chambers of the hydraulic cylinder, then remove the end cover, and then pull out the piston rod and piston for disassembly.
When disassembling the parts, don't beat them forcefully. If it is unavoidable, a copper rod should be used to prevent damage to the parts of the Baler.
Some parts need tools, must use tools, do not beat or pry hard.
Some bolt-fastened parts use thread tightening agent during assembly, which is difficult to disassemble. If disassembling may break the bolts, the exposed part of the bolts can be heated to make the glue fall off before disassembling. .
When disassembling the hydraulic cylinder of the plastic bottle Baler, pay attention to whether there is a hydraulic lock on the cylinder. If so, remove the hydraulic lock first, otherwise there will be pressure from the hydraulic lock in the hydraulic cylinder, which will not only cause difficulty in disassembly, but also easy Cause equipment and personal injury.
When the hydraulic lock is removed, several layers of clean cotton cloth can be used to wrap the connecting part, and then loosen the screw to prevent high-pressure oil from spraying out.
NICKBALER plastic bottle Baling Press machine manufacturers have accumulated mature production technology for many years, and we are committed to providing customers with good service, low-cost and high-quality products. www.nickbaler.net
With the further improvement of our environmental awareness, the utilization rate of beverage bottle Baling Press machines continues to increase.
Individual users ordered beverage bottle Balers that failed due to poor inspections, causing commercial investment failures, production failures and waste of funds.
In order to meet market demand, many manufacturers without production experience and strength are imitating production.
The equipment produced has only appearance, without any substance, and quality cannot be controlled.
Next, let us understand the harmful consequences of not ordering the waste paper baler.
Beverage bottle Balers that cannot be ordered, equipment cannot be used, production cannot be carried out, all investments cannot create value, and the harmful consequences of investment costs cannot be recovered.
For beverage bottle packaging machines, all investments must be at least 300,000 yuan. For ordinary investors, this is definitely not a small amount. It may cause heavy debts and serious bankruptcy consequences.
In view of the serious harmful consequences of the packaging of beverage bottles that are not ordered, you must go to the manufacturer’s site for on-site inspection to determine whether the equipment logo is produced by the manufacturer.
We often encounter customer inquiries about how to choose a horizontal and vertical waste paper baler. What is the difference between the two? Let's analyze this problem for you. Welcome everyone to pay attention.
The vertical waste paper baler is a small-scale baling station or equipment selected in the case of insufficient initial funds. In addition, the vertical baler can pack the waste generated in the production of wool, shreds, rags, etc., and is used on a small scale. The product.
Horizontal waste paper baler is now the mainstream equipment used in waste paper baling stations, which can satisfy more than ten tons of paper per day. Can prepare for future scale expansion.
For raw materials such as yellow cardboard, air-conditioned cartons, etc., you can choose a conventional horizontal waste paper baler, and for raw materials with paper edges, you can choose a small horizontal baler.
If the daily waste paper recycling business volume is large, it is wise to choose a horizontal baler. If the business volume is small, it is recommended to choose a vertical waste paper baler to save the purchase cost.