How to make corn stalks green feed?The traditional method uses an underground fermentation tank,and the most advanced mechanized equipment is a hydraulic green storage baler,which can seal and ferment the straw to improve the quality of the straw green storage.
Silage is to use the lactic acid bacteria present in the green feed to ferment the cut corn stalks under anaerobic conditions to convert part of the sugar source in the feed into lactic acid and reduce the pH value of the silage to below 4.2.
In order to inhibit the reproduction and growth of other aerobic microorganisms such as molds,spoilage bacteria,etc.,so as to achieve the purpose of long-term storage of green fodder corn stalks.
The silage baler can bag corn stalks,and has gradually become a good helper for animal husbandry.It has a wide range of applications and is easy to use.
It is a machine that ferments forage grass through silage bagging.Its characteristics can not only reduce losses,but also will not produce waste and mold,which greatly saves the waste of feed.
Due to the good sealing of plastic bag silage,the quality of the anaerobic fermentation environment of lactic acid bacteria is improved,the nutritional value of the silage is improved,the smell is aromatic,the crude protein content is high,the crude fiber content is low,the digestibility is high,the palatability is good,and the feed intake rate High,the utilization rate of livestock can reach 100%.
Nick brand silage baler has low packaging cost,small size,high compression density,easy transportation and commercialization,and is an ideal assistant for modern livestock silage.
For specific pictures,videos and technical parameters,please visit the website:www.nickbaler.net,or call:86-29-86031588
1. Shearing oil cylinder: It is a double-acting single-piston rod type oil cylinder. Its front end is connected with the frame, and the rear part is connected with the machine base by lower pins (one on each side), and the frame shaft is driven by the push-out and retraction of the piston rod. swing. Implement the cutting action.
2 Frames: The frame is an important flowing part. The left side of the front part is equipped with an upper shear. The middle is connected with the frame by the frame shaft and frame bushing, and the rear is connected with the upper pin shaft of the shear cylinder. .
3. Machine base: It is composed of welding base, left frame, right frame, etc. The right frame and the left frame of the base are welded parts, of which the right and left frames use inner and outer (double) side plates, and the structure is firm.
4. There is a platform and a slope at the front of the machine base, and a lower shear is installed between them. There is a large hole in the middle of the left and right frames for installing the frame, and there is a hole in the rear for installing the shearing cylinder. The front part of the frame is welded with a pressure material cylinder bracket, which is used to install the pressure material cylinder and other portal metal shears.
NICKBALER has rich production experience and integrated services. Using our balers can greatly improve work efficiency and reduce human and financial expenditures. Contact us at 86-29-86031588 or https://www.nkbaler.net/.
The semi-automatic plastic bottle Baling machine is mainly used for Baling machinewaste products, but because it is semi-automatic packing, it needs to be worn manually. Many friends do not know how to operate it. NKBALER has summarized the following points based on experience , I hope it can help everyone.
Semi-automatic plastic bottle Baling machine strapping method:
1. Install the pp tape on the pp tape mounting roller.
2. There is a brake pad connected to the "L"-shaped metal rod on the roller and the fuselage. There are two white rollers on the metal rod. middle.
3. After the upper and lower extensions are inserted, press the connecting spring on the front of the upper extension (the machine is turned on at this time).Line packing.
The above is the method of wearing the semi-automatic plastic bottle baler. I believe that through the introduction, everyone has a deeper understanding of how to operate the plastic baler. If you have other questions, you can leave a message for consultation.https://www.nkbaler.net/.
The electrical control part of the waste paper baler is mainly composed of PLC, motor and electrical components of relays and switches. The most vulnerable parts of these parts are the motor and electrical components. Today we share with you: baler electrical control Box Daily Precautions
1. Pay attention to the grounding, lightning protection, rainproof and moisture-proof of the power cord.
2. Non-professional operators of the electric control cabinet are prohibited from using it.
3. Pay attention to the antifreeze work of the motor and the long-term overload of the motor. Effective prevention of these two items can greatly reduce the damage to the motor, thereby maintaining the normal Baling machineof the waste paper baler.
4. Pay attention to the button operation of the console part, do not use too much force on the switch button, and prevent misoperation to avoid damage caused by short circuit.
The above 4 points are what I want to share with you today, I hope it can help you!
NKBALER provides: horizontal hydraulic baler, vertical hydraulic baler, waste paper baler and other Baling machineequipment, company website: https://www.nkbaler.net/. Tel: 86-29-86031588, looking forward to contacting your cooperation!