News Center
our commitment to nickbaler
Position:Home > News Center <<    Return
Operating standards for plastic hydraulic baler
Author : admin Time : 20-12-18 AllPageView : 210

Nick Machinery's plastic hydraulic baler has good rigidity, toughness and stability, beautiful appearance, convenient operation and maintenance, safe and energy-saving, and low investment cost of equipment basic engineering.

To safely operate the plastic hydraulic baler, you must pay attention to the following items:

1. Before operation, wear work clothes, fasten the cuffs, and the hem of the coat cannot be opened. Do not wear, take off, or wrap around the body beside the machine tool that is running to avoid machine damage. It is necessary to wear safety and labor protection supplies,

2. The operator of the plastic hydraulic baler must be familiar with the main structure, function and use method of the baler.

3. The operator of the plastic hydraulic baler must be trained to master the equipment functions and operating techniques before they can work independently.

微信图片_20201215202826 拷贝.jpg

4. Before operation, sort out all kinds of sundries on the equipment and wipe off any dirt on the hydraulic press rod.

5. It is necessary for the plastic hydraulic baler device to be carried out in the case of power failure to prevent knocking the start button and handle.

6. Install the upper and lower molds to center, adjust the mold gap, and do not allow unilateral violation of the center. After confirming that the mold is fixed, try the pressure again.

7. Before starting the plastic hydraulic baler, start the equipment idling for 5 minutes, and check whether the oil level of the oil tank is satisfied, the sound of the oil pump is normal, and the hydraulic unit, pipes, joints, and pistons are leaking.

Nick Machinery is an enterprise specializing in the production of hydraulic machinery and accessories, allowing you one-stop shopping and worry-free after-sales. Welcome to buy: www.nkbaler.com.


Recommended news
  • The solution to the pressure-free hydraulic system of the waste paper baler

    Common failure phenomenon: the entire hydraulic system of the waste paper baler has no pressure or insufficient pressure.

    Common causes of failure: the overflow valve fails, and the oil pump is not working properly.

    Solution: Check the type of overflow valve used in the waste paper baler equipment. If it is a pilot-operated overflow valve, there are many causes.

    1. The overflow valve is stuck or the solenoid fails. If the overflow valve is stuck, clean the overflow valve and reinstall it. If it is electromagnetic failure, you need to check whether the circuit is open, and check whether the coil of the overflow valve is burned. If there is a problem with the circuit, repair the circuit; if the coil burns out, the coil needs to be replaced.

    2. If it is the internal wear of the overflow valve, the overflow valve needs to be replaced at this time.

    微信图片_20200731152256 拷贝.jpg

    Waste paper baler is an environmental protection equipment that uses hydraulic principles to compress waste paper and waste cardboard into blocks, which is beneficial to waste paper storage, transportation and utilization. https://www.nickbaler.net


  • The oil pump of the horizontal waste paper baler is overheated.

    The oil pump of the horizontal waste paper baler generally has a plunger pump and a vane pump. The reasons for the loud noise of the oil pump system may include: loosening of the fastening screws of the oil pump; wear of the power bearing or stator of the oil pump; serious damage to the oil pump; inside the oil tank Air bubbles, poor oil intake of the hydraulic pump and other reasons will cause this problem. At this time, we should analyze the specific situation and solve the problem of excessive noise in the hydraulic waste paper baler oil pump!

    The possible causes of the failure of the oil pump overheating problem are that the oil pipe is blocked, causing the pressure of the hydraulic oil to increase; the power of the oil pump is too large and overloaded; the hydraulic oil is used unreasonably and the viscosity is too high.

    The quality of the hydraulic oil of the hydraulic waste paper Baler has a great influence on the hydraulic pump. The replacement cycle of the plunger pump is generally one year. If the plunger pump is noisy, it is recommended to consider replacing the plunger pump plunger.

    IMG_20190508_075449 拷贝.jpg

    The waste paper baler is used to extrude waste paper and similar products under normal conditions to greatly reduce the volume, so as to reduce the transportation volume, save the freight, and increase the benefits for the enterprise. https://www.nickbaler.net


  • The first refueling method of horizontal waste paper baler

    The method of refueling the newly purchased waste paper baler equipment before starting, and the oil leakage problem of the newly purchased horizontal waste paper baler equipment has been plagued by the majority of user groups, so how to solve the problem of the waste paper baler oil Well, let's take a look at the waste paper baler equipment with Nick Machinery. What should I pay attention to when using the refueling method?

    1. The oil leakage of the waste paper baler is relatively severe. If the oil pump pressure is adjusted too high, the wear of the movable parts will increase the sealing gap, the sealing device will be damaged, the viscosity of the oil used in the waste paper baler will be too low, etc., which will increase the leakage. After clarifying the reason, adopt the corresponding steps to eliminate it.

    2. Poor heat dissipation, insufficient heat dissipation area of ??the fuel tank, too little oil storage in the fuel tank, resulting in too fast oil circulation, poor cooling of the waste paper Baler cooler, such as failure of cooling water supply or failure of electric fans, high ambient temperature, etc. All are the reasons for poor heat dissipation.

    3. The system does not have an unloading circuit or the unloading circuit does not perform well. When the waste paper baler system does not need to pressurize the oil, the oil is still overflowing to the fuel tank under the working pressure set by the overflow valve or at the unloading pressure Return to the fuel tank downstream in a higher environment. 

    4. Misuse of oil with too high viscosity, the waste paper baler will cause excessive hydraulic loss.

    3-2废纸 (2).jpg

    The horizontal waste paper baler can be customized in different models according to the different needs of customers.https://www.nickbaler.net

Recommended products
  • Cow dung dewatering machine manufacturers
  • Cow dung dring machine price
  • Cow dung compressor, Cow Dung Block Press
  • NK8060T15 Diesel Engine Baler
Recommended Assorises
  • Sack for Used Clothes Packing
  • Semi automatic Strapping Machine
  • Wooden Crusher /Wooden Shredder
  • Hydraulic Forklift Truck
  • Strapping Baling Wire for Baler
  • Pipe Shredder with Hydraulic Balers
Contact Us
  • +86 29 86031588   (Fax)
  • 008615021631102
  • ligoodboy2010
  • sales@nkbaler.com
  • East Qunsheng Road Wuxi City,Jiangsu,China
Inquiry Us
Copyright © 2019 NICKBALER .rights reserved
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top