News Center

our commitment to nickbaler
Position:Home > News Center <<    Return
How to debug a straw hydraulic baler
Author : admin Time : 20-02-12 AllPageView : 833

Straw hydraulic baler has been widely used, before we use the straw hydraulic baler first commissioning, so as to ensure the normal operation of the product, to avoid damage to parts.

We must strictly follow the standard operation, the first operation of the machine before the inspection, the first point is to check the screws and other fasteners without loosening. The second point to the reducer filling liquid lubricants to observe whether the oil flow. Check whether the motor and electrical equipment are dry and the insulation is good. Fourth, check whether the external power supply can drive the operation of the machine, meaning that it is greater than the operation of the machine. After the completion of the commissioning, the machine advanced air operation after the final commissioning is completed, the two proximity switch sensor to the probe shown, the main motor starts, the machine began to send belt, when the two proximity switch sensor to the back of the probe, The main motor stalled, retreated with the motor to start, the machine began to retract, when the two proximity switch sensor to the stop probe is the main motor stop, indicating the normal operation of the machine, which is completed debugging.

We must use the mechanical products before the daily use of straw hydraulic baler debugging work, so that the normal operation of the production, we will continue to develop new equipment for our users to provide more intimate service.


Shaanxi Nick Machinery Equipment Co.,Ltd

www.nkbaler.com

www.nkbaler.net

Facebook:SXnickbaler

Email: info@nkbaler.com

Tel: 86-29-86031588   Fax:86-29-86031588

Mobile :0086-15021631102  

What’s APP:008615021631102

Wechat:ligoodboy2010   

Skype:ligoodboy

Address: RongHao Industry Garden, Xi'an, Shaanxi, China (Head Office )


Recommended news
  • Hydraulic baler cylinder

    The hydraulic baler mainly uses the hydraulic cylinder to "output" objects, but once the hydraulic cylinder has a problem, it will not only affect the normal use, but also need to determine the fault. Today, some customers responded that the hydraulic baler oil cylinder could not go up and down, as if it was stuck. What is the cause? How can we trouble shoot the problem?

    First check the hydraulic baler oil cylinder and eliminate it step by step as follows:

    1.First find a pressure gauge to check the pressure in the valve? And know the stroke and working pressure of the hydraulic cylinder.

    2.Check each fitting on the hydraulic valve block for oil seepage or leakage. And know if the manual generation or the control generation is working properly.

    3.Whether the load when the hydraulic cylinder is loaded is abnormal.

    4.To remove the above is to see if the working pressure of the overflow raft is low, and then adjust it.

    5.If none of the above is to consider whether the cylinder is stuck or there is an obstruction in the valve block.

    NICKBALER machinery provides: horizontal hydraulic baler, vertical hydraulic baler, waste paper baler and other baling machine equipment, company website: www.nkbaler.net, telephone: 86-29-86031588, looking forward to long-term cooperation with you!


  • Process 10 tons of waste paper balers per day?

    How to choose the type to process 10 tons of waste paper every day?

    First of all, NICKBALER suggests that if the daily processing capacity reaches 10 tons, you can choose a horizontal baler, and the horizontal baler is divided into: semi-automatic baler and full-automatic baler; if the initial investment is limited, you can use the semi-automatic baler. Choose from the baler, and the smallest model NKW60BD can meet the production requirements;

    If you have a spacious site and sufficient funds, and have better development and planning in the future,NICKBALER suggests that you can choose a fully automatic baler; what is the difference between a semi-automatic baler and a fully automatic baler?

    1. The architecture is different

    2. Different packing methods

    3. The output is different

    NKW 250Q 01.jpg

    Waste paper baler is our main product for many years, we have very valuable experience, if you want to know more, please follow us https://www.nickbaler.net


  • How to clean the hydraulic system of the baler in the Philippines?

    1. String the baling pressrope of the hydraulic baler through the automatic spring tightening device behind the garbage compressor, and place it along the baling pressbelt groove, then tie the baling press belt to the pull-stop at the bottom of the baling pressgroove, and rotate the automatic spring tightening device 90 degrees , close the bottom door and lock

    2. Put the recycled waste paper, plastic and film waste into the hydraulic baler. When the material is loaded to the height of the pressure plate, close the door tightly and press the "press down" button. The equipment runs automatically and compacts. (The feeding height of materials other than cardboard can only be slightly higher than the bottom door)

    3. The pressure plate moves down and compresses to the maximum pressure and automatically returns to the fully open position. When compressing the baling pressconstraints, the platen stops at the preset position of the compressed material

    4. Open the door of the device and pass the tie rope through the bottom wire groove from front to back and back to the front through the pressure plate wire groove. Tighten the tie rope by hand and tie a knot. Push the baling press rod by hand, push the rod to a fixed position, and clamp it tightly. Press the "Up" button, the return trip of the oil cylinder will automatically turn out the bundled bundles. (When opening the lower door, it is not allowed to go in front of the door。

    Stand up to avoid accidental injury from the door popping open)

    5. After the bale is ejected, reset the bale rod to press down. Finally, remove the bales of waste paper and plastic waste before stacking them for storage, close and lock the door and enter the next packaging cycle task

    NKW250Q 02.jpg

    The hydraulic baler produced by NICKBALER has a simple structure, stable operation, low failure rate and easy cleaning and maintenance. You are welcome to buy https://www.nickbaler.net


Recommended products
  • RDF baler's maintance
  • MSW Vertical Baler Machine
  • MSW Environmental protection equipment
  • MSW Horizontal Hydraulic baler machine
Recommended Assorises
  • Cyclone Separator
  • Diesel engine generator
  • Forklift Car
  • Wire Buckle For Baling
  • Iron Wire For Baling
  • Ton Bags/Jumbo Bag

Contact Us

  • +86 29 86031588   (Fax)
  • 008615021631102
  • ligoodboy2010
  • info@nkbaler.com
  • East Qunsheng Road Wuxi City,Jiangsu,China

Inquiry Us

Copyright © 2019 NICKBALER .rights reserved sitemap.html
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top