News Center

our commitment to nickbaler
Position:Home > News Center <<    Return
Gantry shearing machine improves work efficiency
Author : admin Time : 21-04-21 AllPageView : 366

The hydraulic gantry shear is a kind of renewable resource environmental protection equipment. It ensures that no pollution will occur during the production and processing of renewable resources. The so-called customization means that it can be targeted according to the actual needs and requirements of users. Design a set of exclusive hydraulic shear equipment for users separately, so that users can better use.

Gantry shearing machine is a necessary mechanical equipment in terms of production and processing, and it has a wide range of uses. For example, shearing machines are used in construction and hydraulic work. The main function of the shearing machine is to cut the raw materials of steel. Because its work is very reliable, and it effectively improves work efficiency, it has been fully utilized in recent years.

Let's take a look at the maintenance method of the gantry shearing machine:

1. Operate strictly in accordance with the operating procedures.

2. Add lubricating oil according to the requirements of the lubrication chart every time before starting the machine. The oil should be clean and free of precipitation.

3. The machine tool must be kept clean frequently, and the unpainted part must be anti-rust grease.

4. The lubricating oil in the motor bearings should be replaced and refilled regularly, and the electrical parts should be regularly checked for normal, safe and reliable operation.

龙门剪7-2.jpg

5. Regularly check whether the V-belt, handles, knobs, buttons are damaged, and those with serious wear should be replaced in time, and the spare parts should be reported for supplement.

6. Regularly check and repair switches, insurances, and handles to ensure reliable operation.

7. Lubricate and scrub the machine tool 10 minutes before leaving get off work every day.

8. It is strictly forbidden to operate the equipment by non-designated personnel, and it must be stopped by people off the machine.

Nick mechanical shearing machine is suitable for metal recycling companies, scrap steel mills and other enterprises to perform cold shearing on various shapes of steel and various metal structures.

www.nickbaler.net


Recommended news
  • Process 10 tons of waste paper balers per day?

    How to choose the type to process 10 tons of waste paper every day?

    First of all, NICKBALER suggests that if the daily processing capacity reaches 10 tons, you can choose a horizontal baler, and the horizontal baler is divided into: semi-automatic baler and full-automatic baler; if the initial investment is limited, you can use the semi-automatic baler. Choose from the baler, and the smallest model NKW60BD can meet the production requirements;

    If you have a spacious site and sufficient funds, and have better development and planning in the future,NICKBALER suggests that you can choose a fully automatic baler; what is the difference between a semi-automatic baler and a fully automatic baler?

    1. The architecture is different

    2. Different packing methods

    3. The output is different

    NKW 250Q 01.jpg

    Waste paper baler is our main product for many years, we have very valuable experience, if you want to know more, please follow us https://www.nickbaler.net


  • How to clean the hydraulic system of the baler in the Philippines?

    1. String the baling pressrope of the hydraulic baler through the automatic spring tightening device behind the garbage compressor, and place it along the baling pressbelt groove, then tie the baling press belt to the pull-stop at the bottom of the baling pressgroove, and rotate the automatic spring tightening device 90 degrees , close the bottom door and lock

    2. Put the recycled waste paper, plastic and film waste into the hydraulic baler. When the material is loaded to the height of the pressure plate, close the door tightly and press the "press down" button. The equipment runs automatically and compacts. (The feeding height of materials other than cardboard can only be slightly higher than the bottom door)

    3. The pressure plate moves down and compresses to the maximum pressure and automatically returns to the fully open position. When compressing the baling pressconstraints, the platen stops at the preset position of the compressed material

    4. Open the door of the device and pass the tie rope through the bottom wire groove from front to back and back to the front through the pressure plate wire groove. Tighten the tie rope by hand and tie a knot. Push the baling press rod by hand, push the rod to a fixed position, and clamp it tightly. Press the "Up" button, the return trip of the oil cylinder will automatically turn out the bundled bundles. (When opening the lower door, it is not allowed to go in front of the door。

    Stand up to avoid accidental injury from the door popping open)

    5. After the bale is ejected, reset the bale rod to press down. Finally, remove the bales of waste paper and plastic waste before stacking them for storage, close and lock the door and enter the next packaging cycle task

    NKW250Q 02.jpg

    The hydraulic baler produced by NICKBALER has a simple structure, stable operation, low failure rate and easy cleaning and maintenance. You are welcome to buy https://www.nickbaler.net


  • Daily maintenance of automatic hydraulic balers in India

    1. Before starting the machine, check whether the components of the baler are in good condition; whether the screws and nuts of each component are loose, if so, you need to tighten the screws and nuts, repair personnel to deal with.

    2. Check whether there is any debris blockage inside the machine. The debris blockage will affect the work of the automatic hydraulic baler, so it needs to be removed;

    3. Check whether the knife group and the sliding part are short of oil. If the oil is short, it will cause serious wear on the parts. It must be oiled by dipping and dripping. Use a small stick to dip the oil and slowly drip it on it.

    牛粪01.jpg

    For more information on the fault maintenance and maintenance work of the automatic hydraulic baler, please pay attention to the website of NICKBALER Machinery Company: https://www.nickbaler.net


Recommended products
  • RDF baler's maintance
  • MSW Vertical Baler Machine
  • MSW Environmental protection equipment
  • MSW Horizontal Hydraulic baler machine
Recommended Assorises
  • Cyclone Separator
  • Diesel engine generator
  • Forklift Car
  • Wire Buckle For Baling
  • Iron Wire For Baling
  • Ton Bags/Jumbo Bag

Contact Us

  • +86 29 86031588   (Fax)
  • 008615021631102
  • ligoodboy2010
  • info@nkbaler.com
  • East Qunsheng Road Wuxi City,Jiangsu,China

Inquiry Us

Copyright © 2019 NICKBALER .rights reserved sitemap.html
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top