The cleaning operation of the hydraulic system inside the waste paper baler is very important to the baler, because the waste paper baler needs a good hydraulic system when working. Therefore, in daily work, the cleaning of the baler should not be underestimated and must be taken seriously. Below, let's take a look at the precautions for cleaning the waste paper baler:
When cleaning the waste paper baler, a low-viscosity special cleaning oil should be used. The clean oil is added to the fuel tank of the waste paper baler and heated to 50-80 degrees Celsius. Start the hydraulic pump and let it run dry. When cleaning the baler, you must often knock on the tube. This can remove the attachments. Clean for about 20 minutes. Check the contamination status of the oil filter, and clean the filter, and then clean it again. Repeat until there are not many contaminants on the filter. It’s okay when it’s time.
The cleaning time of waste paper baler is generally 2 hours. For the more messy hydraulic system, each area can be cleaned according to the work area. The hydraulic cylinder can also be connected to allow the hydraulic cylinder to reciprocate to clean the system.
After cleaning, the clean oil must be drained, and the inside of the oil tank must be cleaned. When the waste paper baler system is restored to the normal operating state, add the specified hydraulic oil.
Nick Machinery's waste paper baler has the characteristics of easy installation and operation, safe and reliable use, strong adaptability to the workplace, and reasonable price. www.nickbaler.net
With the development of the economy and the continuous innovation of science and technology, more and more people are now paying attention to environmental protection, and environmental issues have also attracted attention, making the straw baler more popular, and its advantages are becoming more and more prominent. What are the advantages of the straw baler? ? Please see the analysis below
1. It is very versatile, mainly for packing some large or loose items.
2. Save storage space and recycle waste items.
3. The parts of the straw baler have high structural performance and good work efficiency, which reduces labor and transportation costs.
Only a high-quality baler can be better trusted by customers, and only by understanding the performance of the baler, can the straw baler be better utilized and used. Follow NICKBALER, let you grow more https://www.nickbaler.net
Choosing NICKBALER hydraulic baler, independent hydraulic system and servo system control, is the best choice for you to solve and recycle waste. https://www.nickbaler.net
The straw baler must be inspected and maintained at ordinary times to ensure that it can operate normally. While ensuring the characteristics and working efficiency of the straw baler, the following 4 points must be done:
1. Check the screws of each component of the straw baler on time to prevent falling off or bursting;
2. Pay attention to the moisture-proof, waterproof, anti-corrosion and fly-proof of some electrical equipment. The interior of the electrical control cabinet and the terminal block must be kept clean to prevent common failures of electrical equipment;
3. The machine of the straw baler is broken. The two heat-sealing rollers should be in the extended position to prevent the baling machine products from being scalded.
4. Lubricate the junction of each transmission gear, the oil filling hole of the bearing with seat and the oil pump of each movable component of the straw baler on time.
5. When the straw baler is filled with grease, it is not necessary to drop droplets on the transmission belt of the transmission system to prevent damage caused by deviation and vibration or aging of the transmission belt.
For more information about the fault maintenance and maintenance work of the straw baler, please pay attention to the website of NICKBALER M: https://www.nickbaler.net
1. The operator should be strictly trained and qualified before using the machine.
2. When the ambient temperature is less than 2°C above zero, the straw baler is not allowed to be used.
3. When the moisture content of straw and pasture is more than 65%, the straw baler is not allowed to be used.
4. The operator is not allowed to pour liquids such as bacteria water on the baler while bundling.
5. The straw baler is not allowed to have 2 boring cars per hour.
6. When using the motor as power, it is necessary to install the grounding wire.
7. It is necessary to clean up the small silt under the straw baler in time. If there are too many scraps, it may damage the machine parts.
If you are still unclear, you can continue to pay attention to our website https://www.nickbaler.net, and you are welcome to contact us at any time , thank you for reading.
