The power control system of the waste paper baling press machine uses a three-phase four-wire system, which belongs to high-power electricity. For consideration, some precautions should be taken when operating. Mineral water bottle baler This product has good rigidity, toughness and stability, beautiful appearance, convenient operation and maintenance, safety and energy saving, and low investment cost of equipment basic engineering. It is widely used in various types of waste paper mills, used materials recycling companies and other unit enterprises. It is suitable for the packaging and recycling of used waste paper and plastic straws. It is a good equipment to improve labor efficiency, reduce labor intensity, save manpower and reduce transportation costs. Tell you in turn!
1. It is recommended to use a three-phase four-wire system for the input power of the waste paper baler, and it should be compared with ground protection before use. The input leads are recommended to use 3 × 35 + 1 × 10 mm2 cables.
2. Before starting the main motor, check whether the components of each operation control are in the reset state. With the increasing awareness of environmental protection, the waste paper baler has played a great role. It can reuse some waste paper and it is more and more accepted by everyone. The domestic waste paper baler has been In continuous innovation, we are constantly following the development of some advanced technologies abroad.
3. When starting the main motor, first click the "main motor start" button, then press the "main motor stop" button, and observe whether the main motor's rotation direction is not the direction indicated on the label. If not, the waste paper baler should adjust the three-phase power supply. Phase makes it.
Remember: When the motor rotates in the opposite direction to the indicated direction, the time cannot exceed 2 seconds, otherwise the main oil pump will be damaged. The waste paper packing machine is used to squeeze and solidify waste paper and similar products under normal conditions, and use special packaging tape to pack and shape, so that its volume is greatly reduced, so as to reduce the volume of transportation, save freight, and increase benefits for the enterprise. Introduced advanced technology and advanced technology of similar products at home and abroad.
4. Electrical system with phase failure and phase sequence protection. When the main motor does not work after pressing the "main motor start" button, any two wires of the three-phase line can be switched to each other and connected normally.as more information ,please visit :www.nickbaler.net
With the increasing use of waste paper baler machinery, the frequency of use has gradually increased. However, there are still some people who may not know the waste paper baler very well. Some people even think that the waste paper baler is a waste paper recycling machine. Some people even think that it is the evolution of the waste paper basket. In fact, this is not the case. The waste paper baler is actually an existence for more convenient recycling of waste paper. The waste paper baler can compress and integrate waste paper to facilitate recycling and transportation.
People's awareness of environmental protection is getting stronger and stronger, and environmental problems are becoming more and more serious. Every one of us citizens should fulfill their environmental protection obligations and contribute to environmental protection. Therefore, under the background of environmental protection, the waste paper baler came into being and was well received. Our waste paper packaging technology is not particularly perfect, but we are also following in the footsteps of foreign advanced technology, and we are constantly innovating and improving.
The waste paper baler can pack some waste paper for recycling and reuse, which is mainly suitable for some large paper mills or large users of paper products. And the waste paper baler can also recycle old things such as plastic straws.
The application of waste paper baler greatly reduces the loss of manpower and material resources, and is convenient and fast, simple to use, and large-area waste paper baling and recycling is of great significance to environmental protection and avoiding waste.
The cleaning operation of the hydraulic system inside the waste paper baler is very important to the baler, because the waste paper baler needs a good hydraulic system when working. Therefore, in daily work, the cleaning of the baler should not be underestimated and must be taken seriously. Below, let's take a look at the precautions for cleaning the waste paper baler:
When cleaning the waste paper baler, a low-viscosity special cleaning oil should be used. The clean oil is added to the fuel tank of the waste paper baler and heated to 50-80 degrees Celsius. Start the hydraulic pump and let it run dry. When cleaning the baler, you must often knock on the tube. This can remove the attachments. Clean for about 20 minutes. Check the contamination status of the oil filter, and clean the filter, and then clean it again. Repeat until there are not many contaminants on the filter. It’s okay when it’s time.
The cleaning time of waste paper baler is generally 2 hours. For the more messy hydraulic system, each area can be cleaned according to the work area. The hydraulic cylinder can also be connected to allow the hydraulic cylinder to reciprocate to clean the system.
After cleaning, the clean oil must be drained, and the inside of the oil tank must be cleaned. When the waste paper baler system is restored to the normal operating state, add the specified hydraulic oil.
After years of development, waste paper baler has formed a considerable scale, although the scale of development of my country's baler industry has been very large. Nowadays, the development of all walks of life is inseparable from innovation. If the vertical waste paper baler can be developed in terms of technological innovation, at the same time in response to the call of the country, it will also bring more economy to the vertical waste paper baler equipment enterprises. interest.
The new technology of vertical waste paper baler can increase the output of equipment. Although my country's waste paper baler industry has developed so fast in the past two years and the export volume has increased significantly, it is undeniable that there are still many shortcomings in the vertical waste paper baler.
If these problems are not improved in a short time, it will inevitably affect the development of the baler industry and the position of the vertical waste paper baler in the baler industry. The concentration of my country's baler industry is not enough, production capacity is scattered, and economies of scale cannot be formed. At present, the production capacity of the vertical waste paper baler has developed rapidly, but the technological progress of the industry is relatively slow, and the R&D and innovation capabilities are low. The service life and reliability of the vertical waste paper baler have gradually been unable to meet the needs of technological development. Therefore, technological innovation is urgently needed.
The vertical waste paper baler is currently still stuck on capacity expansion, which makes China's baler industry lack a certain brand effect. Therefore, in terms of technological innovation of vertical waste paper baler, we must increase efforts to make contributions to my country's baler industry.
The quality of the vertical waste paper baler is inseparable from the oil cylinder, and the function of the oil cylinder determines the stability of the baler. Similarly, the quality of hydraulic oil also affects the failure rate and service life of the cylinder. The cylinder needs to use No. 46 anti-wear hydraulic oil to ensure the efficient production of the baler.
In the current baler industry, many small manufacturers are reluctant to develop and research new products, and will blindly imitate the products of large baler manufacturers. This is also an important factor leading to the slow development of the waste paper baler market.
With the management philosophy of "Integrity creates the brand, and quality determines the future", Nick Machinery continues to improve the mechanism, strengthen brand awareness, and make products with excellent quality and better after-sales service. www.nickbaler.net