Using the brand packer technology, it is designed to have dual circuit control of the whole machine, which is more stable and reliable than the previous single circuit control. The dual circuit control reduces the internal load of the machine's electrical board, and the operation of each circuit of the packer structure is smoother and more stable.
So what are the requirements for the use of Hydraulic baler oil by the baler?
1. In areas where fire protection is required, the Hydraulic baler oil's rich ignition point should be high; in cold climate areas, the Hydraulic baler oil's freezing point should be low.
2. The Hydraulic baler oil should not be easy to oxidize, avoid colloid and asphaltene due to oxidation, and make the Hydraulic baler oil degenerate. Oxide impurities can also block the Hydraulic baler oil circuit and damage the normal operation of the hydraulic system.
3. It has no effect on human health.
4, clean quality, no impurities. If there is moisture, it will reduce the smooth function of the straw baler Hydraulic baler oil; there are mechanical impurities that will block the orifices and the valve core jam; acid and alkali will corrode the metal and damage the seal structure; there will be volatile substances that will change the Hydraulic baler oil Thick and air bubbles occur, which damages the smoothness of the transmission.
5, has outstanding smooth function. In the hydraulic system of the baler, the working fluid is not only used to transfer energy, but also has a smooth effect on the conflicting surfaces of the hydraulic components. In some machine tools, the Hydraulic baler oil source for the smooth system of the machine tool comes from the hydraulic system, and the hydraulic system uses the same Hydraulic baler oil pump to supply Hydraulic baler oil. Therefore, hydraulic Hydraulic baler oil should have high Hydraulic baler oil film strength and outstanding smooth function within the operating temperature and pressure change scale to avoid dry conflicts.as more information ,please visit us : www.nickbaler.net.
With the increasing use of waste paper baler machinery, the frequency of use has gradually increased. However, there are still some people who may not know the waste paper baler very well. Some people even think that the waste paper baler is a waste paper recycling machine. Some people even think that it is the evolution of the waste paper basket. In fact, this is not the case. The waste paper baler is actually an existence for more convenient recycling of waste paper. The waste paper baler can compress and integrate waste paper to facilitate recycling and transportation.
People's awareness of environmental protection is getting stronger and stronger, and environmental problems are becoming more and more serious. Every one of us citizens should fulfill their environmental protection obligations and contribute to environmental protection. Therefore, under the background of environmental protection, the waste paper baler came into being and was well received. Our waste paper packaging technology is not particularly perfect, but we are also following in the footsteps of foreign advanced technology, and we are constantly innovating and improving.
The waste paper baler can pack some waste paper for recycling and reuse, which is mainly suitable for some large paper mills or large users of paper products. And the waste paper baler can also recycle old things such as plastic straws.
The application of waste paper baler greatly reduces the loss of manpower and material resources, and is convenient and fast, simple to use, and large-area waste paper baling and recycling is of great significance to environmental protection and avoiding waste.
The cleaning operation of the hydraulic system inside the waste paper baler is very important to the baler, because the waste paper baler needs a good hydraulic system when working. Therefore, in daily work, the cleaning of the baler should not be underestimated and must be taken seriously. Below, let's take a look at the precautions for cleaning the waste paper baler:
When cleaning the waste paper baler, a low-viscosity special cleaning oil should be used. The clean oil is added to the fuel tank of the waste paper baler and heated to 50-80 degrees Celsius. Start the hydraulic pump and let it run dry. When cleaning the baler, you must often knock on the tube. This can remove the attachments. Clean for about 20 minutes. Check the contamination status of the oil filter, and clean the filter, and then clean it again. Repeat until there are not many contaminants on the filter. It’s okay when it’s time.
The cleaning time of waste paper baler is generally 2 hours. For the more messy hydraulic system, each area can be cleaned according to the work area. The hydraulic cylinder can also be connected to allow the hydraulic cylinder to reciprocate to clean the system.
After cleaning, the clean oil must be drained, and the inside of the oil tank must be cleaned. When the waste paper baler system is restored to the normal operating state, add the specified hydraulic oil.
After years of development, waste paper baler has formed a considerable scale, although the scale of development of my country's baler industry has been very large. Nowadays, the development of all walks of life is inseparable from innovation. If the vertical waste paper baler can be developed in terms of technological innovation, at the same time in response to the call of the country, it will also bring more economy to the vertical waste paper baler equipment enterprises. interest.
The new technology of vertical waste paper baler can increase the output of equipment. Although my country's waste paper baler industry has developed so fast in the past two years and the export volume has increased significantly, it is undeniable that there are still many shortcomings in the vertical waste paper baler.
If these problems are not improved in a short time, it will inevitably affect the development of the baler industry and the position of the vertical waste paper baler in the baler industry. The concentration of my country's baler industry is not enough, production capacity is scattered, and economies of scale cannot be formed. At present, the production capacity of the vertical waste paper baler has developed rapidly, but the technological progress of the industry is relatively slow, and the R&D and innovation capabilities are low. The service life and reliability of the vertical waste paper baler have gradually been unable to meet the needs of technological development. Therefore, technological innovation is urgently needed.
The vertical waste paper baler is currently still stuck on capacity expansion, which makes China's baler industry lack a certain brand effect. Therefore, in terms of technological innovation of vertical waste paper baler, we must increase efforts to make contributions to my country's baler industry.
The quality of the vertical waste paper baler is inseparable from the oil cylinder, and the function of the oil cylinder determines the stability of the baler. Similarly, the quality of hydraulic oil also affects the failure rate and service life of the cylinder. The cylinder needs to use No. 46 anti-wear hydraulic oil to ensure the efficient production of the baler.
In the current baler industry, many small manufacturers are reluctant to develop and research new products, and will blindly imitate the products of large baler manufacturers. This is also an important factor leading to the slow development of the waste paper baler market.
With the management philosophy of "Integrity creates the brand, and quality determines the future", Nick Machinery continues to improve the mechanism, strengthen brand awareness, and make products with excellent quality and better after-sales service. www.nickbaler.net