News Center
our commitment to nickbaler
Position:Home > News Center <<    Return
Nick Baler Waste paper Baling Machine introduces equipment maintenance methods
Author : admin Time : 20-04-07 AllPageView : 429

Hydraulic Nick Baler Waste paper Baling Machine introduces equipment maintenance methods. Hydraulic Nick Baler Waste paper Baling Machine is easy to operate and is accepted by more and more companies. However, as the packer is continuously used every day, even the best products have a period of use.

In addition to the quality of Nick Baler Waste Paper Baling Machine itself, how to increase the life of Nick Baler Waste Paper Baling Machine and reduce the failure rate as much as possible, so that it can play a high utilization value has become a concern of many enterprises.

The following is the maintenance and maintenance of hydraulic Nick Baler Waste paper Baling Machine.

 How much do you know about the advantages of Nick Baler Waste paper Baling Machine equipment? According to the prospect of progress in the times, technological products are also constantly developing. If you have used it, you must know how many advantages of Nick Baler Waste paper Baling Machine. If you have never used it, then you can just consider it. I started to like Nick Baler Waste paper Baling Machine.

mmexport1525170858847.jpg

   1. It is recommended to install an oil-water separator, the air source is dry: the general air source is relatively humid, the hydraulic Nick Baler Waste paper Baling Machine will cause unstable performance due to the entry of moisture, and will cause damage in the long run. Before use, the oil storage of the oil-water separator oil storage tank should be at least 2/3, and the water in the water storage tank should be drained regularly.

   2. The choice of Nick Baler Waste paper Baling Machine is also very important, the inner diameter is generally 8-10mm; the length of the trachea is generally not more than 15-20m. Fully automatic Nick Baler Waste paper Baling Machine is an electromechanical integration product, mainly composed of mechanical system, control system, feeding system and power system. The whole packaging process is composed of auxiliary time such as pressing, returning, lifting, transferring, ascending, ascending, and receiving. If the trachea is too long, consider adding a booster device in the middle, which will affect the performance of the baler equipment.

   3. Before each operation of the baler, please take a few minutes to check whether the air source is working properly and the hydraulic pressure is stable. The air pressure of the baler is preferably 0.7MPa.

   4. When using, adjust whether the baler's pulling force can be determined by the sound when the baler is working. Nick Baler Waste paper Baling Machine With the increasing awareness of environmental protection, Nick Baler Waste paper Baling Machine has played a big role. It can reuse some waste paper and is more and more accepted by everyone. Domestic Nick Baler Waste paper Baling Machine has been constantly innovating and following the development of some advanced technologies abroad. The louder the sound, the stronger the pull, and vice versa.

   5. To develop the good habit of diligently adding lubricating oil, according to the frequency of use of the baler, regularly add appropriate amount of lubricating oil to the air inlet of the baler to reduce wear.

   6. After working for a long time, you should use a wire brush to clean the broken plastic belt on the tightening wheel and the anti-slip plate.

   7. After the work is completed or during non-working hours, the air source is turned off. Misoperation control will cause the baler to run without belt, resulting in wear of wearing parts.

   8. When Nick Baler Waste paper Baling Machine fails, please ask after-sales personnel or experienced personnel to disassemble and repair it.

Nick Baler Waste paper Baling Machine is simple to operate. Because there is no need for manual operation in the entire operation process, that is, the entire workflow can be completed by the operation of buttons. So there will be no accidents due to some temporary machine failure during operation. You can decide the size of Nick Baler Waste paper Baling Machine yourself.for information ,please visit :www.nickbaler.net 

Recommended news
  • Precautions for Australian textile balers

    The textile packing machine force is widely used in various garment factories, garment recycling stations and other units and enterprises. It is suitable for packing and recycling textiles and fabric strips. It is a good equipment to improve labor efficiency, reduce labor intensity, and reduce transportation costs.

    Precautions for textile baler:

    1. Pay attention to the grounding of the power cord, lightning protection, rain protection and moisture protection.

    2. It is forbidden to use the hydraulic packing electric control cabinet by non-operators.

    3. Pay attention to the antifreeze work of the motor and the long-term overload of the motor. Effective prevention of these two can reduce the damage of the motor and maintain the normal packaging of the textile baler.

    4. Pay attention to the button operation of the console. Don't use too much force on the switch button, and prevent misoperation to avoid damage caused by short circuit.

    cc561b38ee076be9aa635a9ef866467 拷贝.jpg

    NICKBALER clothing baler is based on market demand. The products start from simple and reasonable energy saving and pay attention to practicability, so as to serve more new and old customers. www.nickbaler.net

  • American clothing packing machine supplier

    The dedicated vertical garment packing machine is divided into two kinds of single oil cylinder and double oil cylinder. It is mainly used for compressing and packing various garments, which is quick and easy to pack.

    It is widely used for compression packaging of various garments such as cloth, textiles, sweaters, shirts, sweaters, underwear, socks, and export garments.

    All doors of the equipment can be opened, and the packing is convenient. It adopts hydraulic manual control. It has the characteristics of simple operation, high packing efficiency, low investment cost, and multiple selection of pressing plate stroke parameters.

    The ideal effect can be achieved by selecting the pressing plate stroke for compressing various garments. The inner box can be made of stainless steel, which saves manpower, improves labor efficiency, reduces labor intensity, and reduces transportation costs.

    5-2服装.jpg

    NICKBALER is a professional service manufacturer specializing in the development, production, sales and service of hydraulic machinery and packaging machinery. www.nickbaler.net

  • Preparation of plastic bottle Baling Press machine

    Now that the application of plastic bottle balers has become more and more extensive, what preparations should we make when applying this product?

    Next, let's follow the editor to find out.

    The plastic bottle baler works for a long time and reaches a certain service life. In order to make the equipment play the overall value, the old parts need to be replaced. There are several aspects that need attention in the process of replacing the cylinder of the plastic bottle baler.

    According to the correct disassembly method, on the one hand, the disassembly process is smooth and not damage the equipment; on the other hand, it is also to take care of safety issues.

    Before disassembling the hydraulic cylinder of the mineral water bottle Baler, drain the hydraulic oil in the two chambers of the hydraulic cylinder, then remove the end cover, and then pull out the piston rod and piston for disassembly.

    When disassembling the parts, don't beat them forcefully. If it is unavoidable, a copper rod should be used to prevent damage to the parts of the Baler.

    Some parts need tools, must use tools, do not beat or pry hard.

    Some bolt-fastened parts use thread tightening agent during assembly, which is difficult to disassemble. If disassembling may break the bolts, the exposed part of the bolts can be heated to make the glue fall off before disassembling. .

    When disassembling the hydraulic cylinder of the plastic bottle Baler, pay attention to whether there is a hydraulic lock on the cylinder. If so, remove the hydraulic lock first, otherwise there will be pressure from the hydraulic lock in the hydraulic cylinder, which will not only cause difficulty in disassembly, but also easy Cause equipment and personal injury.

    net.jpg

    When the hydraulic lock is removed, several layers of clean cotton cloth can be used to wrap the connecting part, and then loosen the screw to prevent high-pressure oil from spraying out.

    NICKBALER plastic bottle Baling Press machine manufacturers have accumulated mature production technology for many years, and we are committed to providing customers with good service, low-cost and high-quality products. www.nickbaler.net


Recommended products
  • Cow dung compressor, Cow Dung Block Press
  • NK8060T15 Diesel Engine Baler
  • Wood Shaving Bedding Machine
  • PET Bottle Baling Press Nick Baler
Recommended Assorises
  • Sack for Used Clothes Packing
  • Semi automatic Strapping Machine
  • Wooden Crusher /Wooden Shredder
  • Hydraulic Forklift Truck
  • Strapping Baling Wire for Baler
  • Pipe Shredder with Hydraulic Balers
Contact Us
  • +86 29 86031588   (Fax)
  • 008615021631102
  • ligoodboy2010
  • sales@nkbaler.com
  • East Qunsheng Road Wuxi City,Jiangsu,China
Inquiry Us
Copyright © 2019 NICKBALER .rights reserved
Whats App Skype Shaanxi Nick Machinery
Equipment Co. LTD
go back to the top